A method for extracting soil DNA using a soil centrifuge
Release time:
2015-03-11
Overview:
1. Weigh 5 g of the soil sample and add it to sterilized quartz sand. Do not use liquid nitrogen for grinding, as this can cause significant DNA damage and result in nearly complete fragmentation of the DNA fragments. At this step, you can also add PBS to wash the soil—this serves two purposes: first, it helps remove some impurities; second, it keeps the soil in a suspended state. Then, vigorously vortex the mixture for 2–3 minutes using a vortex mixer to break up the soil particles. Next, centrifuge the soil suspension at 12,000 rpm for 5 minutes, and discard the supernatant.
2. Add 13.5 mL of DNA extraction buffer and 100 μL of 20 mg/mL proteinase K, then incubate at 37℃ with shaking at 225 rpm for 2 hours.
3. Add 700 μL of 20% SDS, place in a 65℃ water bath for 2 hours, and invert and mix several times every 15 minutes.
4. Centrifuge at 6,000 rpm at room temperature for 15 minutes, and collect the middle liquid phase. Add 3 mL of DNA extraction solution and 300 μL of 20% SDS to the precipitate, then place the mixture in a 65℃ water bath for 30 minutes. Perform another centrifugation as described above, collect the middle liquid phase, and combine the fractions. Repeat this procedure once more. At this stage, you might consider performing an additional extraction step. Alternatively, you could use 5 mL instead of 3 mL. If the final volume becomes too large to fit into a single tube, you can divide the sample into two 50-mL centrifuge tubes and proceed with centrifugation.
5. Add an equal volume of chloroform:isoamyl alcohol (24:1) to the collected liquid phase, perform a single extraction, and centrifuge at 8000 rpm for 10 minutes; then collect the upper liquid phase. During the extraction process, it is recommended to include an additional step using phenol-chloroform, as phenol can better denature proteins. If you choose not to use phenol, we recommend performing two extractions with chloroform:isoamyl alcohol instead. You’ll find that the color will become significantly clearer.
6. In the liquid phase collected in Step 5, add sodium acetate at a volume of 0.1 times the volume of the liquid phase and isopropanol at a volume of 0.6 times the volume of the liquid phase; then allow the mixture to stand at room temperature for 1–2 hours.
7. Centrifuge the precipitate at 12,000 rpm for 15 minutes, then discard the supernatant. Add 10 mL of cold ethanol to the precipitate, wash it, and centrifuge at 12,000 rpm for 5 minutes; discard the supernatant. Finally, centrifuge at 12,000 rpm for 30 seconds, and use a pipette to remove any remaining liquid.
8. Allow the precipitate to air-dry naturally at room temperature. After drying, add 400 μL of TE buffer to dissolve the precipitate. The precipitate adheres tightly to the wall of the container; do not use a small pipette to blow or aspirate and disturb it. Instead, immerse the precipitate completely in the TE buffer and leave it at 4°C overnight or for several hours—this will loosen the precipitate.
The soil sample is rather unusual—black in color and rich in humic substances and other organic materials. This sample must be purified. Since it contains excessive amounts of polysaccharides and humic substances, I’d recommend using Qiagen’s 40-kb gel recovery kit. If you think that’s too expensive, you could consider electroelution instead.
DNA extraction solution composition: 100 mM Tris, 100 mM EDTA, 200 mM NaCl, 2% PVPP, 3% CTAB, pH 9.0
The above details the procedure for the three extractions, along with the amounts of reagents used.
Important note: All needle tips, including those for 1 mL, must be sterilized after being sharpened. Each step should be performed gently to ensure the DNA remains intact.