When designing a centrifuge, the primary consideration is the structural aspect.
Release time:
2015-08-17
Overview:
Shanghai Luxiangyi Centrifuge Based on years of technological expertise, the instrument company has discovered that during operation, liquid and gas phases can seep into the centrifuge, causing corrosion on the tapered surface of the main shaft and even penetrating into the bearings, thereby damaging them and affecting the normal operation of the machine. Although upper bearing covers are typically equipped with skeleton-type seals and other similar structures, a portion of the space between the upper bearing cover and the conical hole of the rotor drum remains exposed. As a result, the gas phase within the centrifuge’s internal cavity may corrode the exposed surfaces of the main shaft. Since the materials separated in the pharmaceutical industry often contain organic solvents or media such as acids, bases, and salts, it is crucial to fully consider the sealing requirements for these areas when ordering equipment and to incorporate either dynamic or static sealing structures to meet these demands. Whether the centrifuge operates in a non-sterile or sterile environment, its use places stringent demands on environmental conditions. In high-grade environments—such as sterile workshops classified as Class 10,000 or Class 100,000—excellent sealing performance ensures effective isolation between the external environment and the machine’s interior. The solid, liquid, and gas phases within the internal cavity must be completely isolated from both operators and the external environment to prevent cross-contamination.
In terms of design and structure, centrifuges primarily take the following three aspects into consideration:
(1) Basic technology is crucial and can ensure the implementation of CIP.
(2) In centrifuges with scraper discharge, the structural design must incorporate an automatic device for removing residual filter cake. High-pressure gas is passed through holes in the basket frame, causing the filter cloth to undergo a slight elastic deformation, which in turn shakes the filter cake into the solid-discharge pipe, significantly reducing the working time required for cake removal. Furthermore, when combined with an automated CIP system, this approach not only ensures high production efficiency but also enhances the effectiveness of the CIP process.
(3) The design of the centrifugal basket differs from that of commonly used vertical centrifuges. In conventional designs, the basket frame typically requires reinforcing hoops—ranging from as few as two to more than four. Usually, the connection between the hoops and the basket frame is achieved through gap welding. This structural design poses challenges for thorough cleaning. Tianjin University has conducted studies on three-legged centrifuges both with and without reinforcing hoops. Centrifuge After extensive research on the deformation behavior during drum rotation and a comparison of the radial stresses on the inner surface of the drum wall, it has been found that while stiffening hoops do help alleviate inter-ring stresses, they also exacerbate radial stresses. Moreover, under normal operating conditions, stiffening hoops fail to significantly improve the stresses in the rotating drum wall. In most cases, stiffening hoops serve merely as a protective measure when the drum itself is about to fail.
Therefore, it can be concluded that, with appropriately reinforced wall thickness of the centrifuge basket, a design without reinforcing hoops would be preferable, while also creating favorable conditions for CIP. Secondly, in the structural design, attention should be paid to the issue of contamination caused by foreign particles generated during operation—such as contaminants from the centrifugal clutch’s throw-out weights, contaminants from brake bands, foreign particles resulting from friction between belts and pulleys, debris from wear of components in the transmission system, and leakage of lubricants.
Place the substances to be separated into the centrifuge tubes provided with the centrifuge, and insert these tubes into the corresponding holes in the rotor. (However, the amount of substance added to each centrifuge tube must be roughly equal.) Close the lid, connect the power supply, and turn on the power switch. Once the power indicator light comes on, set the “Timer” dial to your desired centrifugation time or to the “Always On” position (the farthest counterclockwise stop). At this point, the centrifuge will enter operation mode. The speed control allows you to select the desired centrifugation speed, typically ranging from about 500 to 4,000 revolutions per minute. You can adjust the speed setting to an appropriate level based on your specific needs.
According to the working principle of a centrifuge, the screw and the drum rotate concentrically and in the same direction. However, there is a speed difference between the two. If nn represents the absolute rotational speed of the drum and ns represents the absolute rotational speed of the screw, and an denotes the differential rotational speed between the two, then an = nn - ns. When the drum’s rotational speed is faster than that of the screw—that is, when nn > ns—this results in a negative differential rotational speed. The slip rate is defined as the ratio of the differential rotational speed to the drum’s rotational speed: slip rate a = (an / nn) × 100%. (Typically, a ranges from 0.2% to 3%.) In crystallization separation processes using recovery equipment, the goal is to achieve a high degree of dryness in the solid phase. Utilizing a negative slip rate in this context facilitates the conveyance of the settled solids and reduces the power transmitted through the gearbox. A negative slip rate can be achieved by adjusting the differential rotational speed between the drum and the screw—for instance, by modifying the dimensions of the pulleys on the rotor to alter the slip rate. This method is relatively easy to implement in industrial practice.
In addition, belt aging or uneven belt tension can also cause variations in the rotational speed difference, thereby affecting the solid-phase discharge. This is an important point to keep in mind when analyzing the solid-phase discharge from a centrifuge. Although some digital displays (such as those that use a knob to select a value and then show it digitally) have improved readability, their underlying principle for value acquisition remains unchanged and still relies on analog technology. A typical digital display, by contrast, features a user-friendly interface, keyboard operation, digital display, and fully computer-controlled programmable functions. Centrifuge The core is intelligent control, which is realized by a computer.
Previous: