How to ensure the safety and centrifugation performance of a refrigerated centrifuge
Release time:
2015-09-01
Overview:
Frozen centrifuge
To ensure Frozen centrifuge For safety and optimal centrifugal performance, the instrument must be placed on a sturdy, level work surface. No items should be placed on the engineering-plastic cover door. Samples must be loaded symmetrically, and before starting the machine, ensure that all nuts are securely tightened. Before use, inspect the rotor for any signs of damage or corrosion. Also, check the centrifuge tubes for cracks, aging, or other defects. If you notice any doubts, immediately stop using the equipment and contact the manufacturer. Before starting the machine, be sure to tighten the clamping nut on the rotor to prevent the high-speed rotating rotor from flying off and causing an accident. The set rotational speed must not exceed the maximum allowable speed to ensure safe operation of the machine. During operation of the refrigerated centrifuge, if the display shows “0.00” or any other non-zero number, indicating that the machine is not functioning, immediately turn off the power and unplug the unit. Wait 10 seconds before restarting the machine. Once the set rotational speed is displayed, press the “Run” button to resume normal operation. If the specific gravity of the sample to be separated exceeds 1.2 grams per cubic centimeter, the maximum rotational speed N must be adjusted according to the following formula: N = NMAX × (1.2 / Sample Specific Gravity)^0.5, where NMAX is the rotor’s maximum rated speed. Under no circumstances should you open the cover door while the machine is running or when the rotor has not yet come to a complete stop, to avoid accidents.
The centrifuge tubes in a refrigerated centrifuge must be filled with equal volumes of sample; never allow the rotor to operate under unbalanced conditions. It is best not to run the centrifuge for more than 60 minutes at a time. The machine must be reliably grounded; when not in use, unplug the power cord. Low-temperature separation technology using refrigerated centrifuges is an indispensable tool in molecular biology research. Whether it’s the isolation of gene fragments, the precipitation and recovery of enzyme proteins, or the preparation of other biological samples, low-temperature centrifugation is essential. Therefore, refrigerated centrifuges have become crucial instruments in molecular biology research. The refrigerated centrifuge should be placed on a level, sturdy floor or platform, and care should be taken to ensure that the machine remains perfectly horizontal to prevent vibrations during centrifugation. Turn on the power switch, install the required rotor according to specifications, and place the pre-balanced samples—carefully balanced using a precision balance—onto the rotor’s sample holders (the centrifuge tubes must be balanced simultaneously with the samples). Then, close the machine’s lid. Press the function-selection key and set the desired parameters: temperature, speed, duration, acceleration, and deceleration. For machines equipped with computer control, also press the storage key to save all entered settings. Finally, press the start button. Frozen centrifuge The above-mentioned parameters will be applied, and the machine will automatically shut down at the preset time. After the refrigerated centrifuge has completely stopped rotating, open the lid, remove the centrifuged samples, and use a soft, clean cloth to wipe clean the rotor and the inner walls of the chamber. Only after the temperature inside the centrifuge chamber has nearly reached room temperature can you close the lid again.
The chamber lid (door), rotor cover, and centrifuge caps of the refrigerated centrifuge are all fitted with oil-resistant rubber O-rings of varying thicknesses and sizes. These O-rings serve to block atmospheric pathways during the vacuuming process, ensuring that the container maintains either the desired vacuum or atmospheric pressure. During vacuuming, the sealing ring on the centrifuge chamber door prevents external air from entering, thereby maintaining a consistently high degree of vacuum inside the chamber. Conversely, the sealing rings inside the rotor cover and centrifuge tube caps serve precisely the opposite purpose: they prevent vacuum from penetrating into the centrifuge chamber, keeping the pressure inside the centrifuge rotor equal to atmospheric pressure. If the rotor and tube cap seals are inadequate, samples may leak out, directly affecting experimental results. Moreover, such leakage can create negative pressure both inside the centrifuge tubes and within the rotor itself, making it increasingly difficult to open the tube caps and rotor covers. Thus, the critical importance of proper sealing becomes evident.
When the refrigerated centrifuge is in the pre-cooling state, the centrifuge lid must be closed. After the centrifugation is complete, when removing the rotor, place it upside down on the laboratory bench, wipe dry any remaining water inside the chamber, and leave the centrifuge lid open. During pre-cooling, the rotor cover can be placed either on the centrifuge’s platform or on the laboratory bench; under no circumstances should it be left floating loosely on the rotor, as an accidental start-up could cause the rotor cover to fly off, leading to an accident! After tightening the rotor cover, be sure to use your fingers to check that there is no gap between the rotor and the rotor cover. If you detect any gaps, loosen and retighten the cover until you confirm there is a seamless fit before starting the centrifuge. Frozen centrifuge During the centrifugation process, operators must not leave the centrifuge room. If any abnormal situation occurs, operators must not turn off the power supply (POWER); instead, they should press the STOP button. Before pre-cooling, operators must complete the centrifuge usage log. Only high-quality centrifuge tubes—free from defects—may be used; counterfeit or substandard tubes are strictly prohibited, as are aged, deformed, or cracked centrifuge tubes. On holidays and during evening hours, operators may leave only after performing the routine safety inspection following the last use of the centrifuge. In the event of a machine malfunction or component damage during instrument operation, operators must promptly contact technical personnel.
The centrifuge tubes in a refrigerated centrifuge must be filled with equal volumes of sample; never allow the rotor to operate under unbalanced conditions. It is best not to run the centrifuge for more than 60 minutes at a time. The machine must be reliably grounded; when not in use, unplug the power cord. Low-temperature separation technology using refrigerated centrifuges is an indispensable tool in molecular biology research. Whether it’s the isolation of gene fragments, the precipitation and recovery of enzyme proteins, or the preparation of other biological samples, low-temperature centrifugation is essential. Therefore, refrigerated centrifuges have become crucial instruments in molecular biology research. The refrigerated centrifuge should be placed on a level, sturdy floor or platform, and care should be taken to ensure that the machine remains perfectly horizontal to prevent vibrations during centrifugation. Turn on the power switch, install the required rotor according to specifications, and place the pre-balanced samples—carefully balanced using a precision balance—onto the rotor’s sample holders (the centrifuge tubes must be balanced simultaneously with the samples). Then, close the machine’s lid. Press the function-selection key and set the desired parameters: temperature, speed, duration, acceleration, and deceleration. For machines equipped with computer control, also press the storage key to save all entered settings. Finally, press the start button. Frozen centrifuge The above-mentioned parameters will be applied, and the machine will automatically shut down at the preset time. After the refrigerated centrifuge has completely stopped rotating, open the lid, remove the centrifuged samples, and use a soft, clean cloth to wipe clean the rotor and the inner walls of the chamber. Only after the temperature inside the centrifuge chamber has nearly reached room temperature can you close the lid again.
The chamber lid (door), rotor cover, and centrifuge caps of the refrigerated centrifuge are all fitted with oil-resistant rubber O-rings of varying thicknesses and sizes. These O-rings serve to block atmospheric pathways during the vacuuming process, ensuring that the container maintains either the desired vacuum or atmospheric pressure. During vacuuming, the sealing ring on the centrifuge chamber door prevents external air from entering, thereby maintaining a consistently high degree of vacuum inside the chamber. Conversely, the sealing rings inside the rotor cover and centrifuge tube caps serve precisely the opposite purpose: they prevent vacuum from penetrating into the centrifuge chamber, keeping the pressure inside the centrifuge rotor equal to atmospheric pressure. If the rotor and tube cap seals are inadequate, samples may leak out, directly affecting experimental results. Moreover, such leakage can create negative pressure both inside the centrifuge tubes and within the rotor itself, making it increasingly difficult to open the tube caps and rotor covers. Thus, the critical importance of proper sealing becomes evident.
When the refrigerated centrifuge is in the pre-cooling state, the centrifuge lid must be closed. After the centrifugation is complete, when removing the rotor, place it upside down on the laboratory bench, wipe dry any remaining water inside the chamber, and leave the centrifuge lid open. During pre-cooling, the rotor cover can be placed either on the centrifuge’s platform or on the laboratory bench; under no circumstances should it be left floating loosely on the rotor, as an accidental start-up could cause the rotor cover to fly off, leading to an accident! After tightening the rotor cover, be sure to use your fingers to check that there is no gap between the rotor and the rotor cover. If you detect any gaps, loosen and retighten the cover until you confirm there is a seamless fit before starting the centrifuge. Frozen centrifuge During the centrifugation process, operators must not leave the centrifuge room. If any abnormal situation occurs, operators must not turn off the power supply (POWER); instead, they should press the STOP button. Before pre-cooling, operators must complete the centrifuge usage log. Only high-quality centrifuge tubes—free from defects—may be used; counterfeit or substandard tubes are strictly prohibited, as are aged, deformed, or cracked centrifuge tubes. On holidays and during evening hours, operators may leave only after performing the routine safety inspection following the last use of the centrifuge. In the event of a machine malfunction or component damage during instrument operation, operators must promptly contact technical personnel.