The Application of Centrifuges in Bacteriological Diagnostic Isolation and Cultivation
Release time:
2012-10-29
Overview:
Centrifuges are typically used to separate samples by centrifugation. The centrifugal separation and culture technique for bacteria is an important and fundamental procedure in bacteriological diagnosis.
In bacteriological diagnostic work, it is often necessary to isolate bacteria from the sample material and obtain pure cultures—cultures consisting of a single bacterial species. Therefore, centrifuges are commonly used to separate samples by centrifugation. The technique of centrifugal separation and cultivation of bacteria is an important and fundamental procedure in bacteriological diagnostics.
There are many methods for separating bacteria, and the following are some commonly used ones.
The material to be examined is inoculated onto a suitable culture medium, and then individual colonies growing on the surface of the solid medium are selected for isolation. These selected colonies are transferred to another suitable culture medium for further cultivation. Since a single colony typically originates from the growth and reproduction of a single bacterium, the bacteria cultivated in this way are of a single species—known as a pure culture.
Isolate bacteria using special culture environments (such as anaerobic or carbon dioxide environments, etc.).
The material to be tested is inoculated into susceptible animals, allowing the pathogenic bacteria to multiply within the animal body. Subsequently, samples are collected from the animals and subjected to centrifugation to separate and isolate the desired components, which are then cultured. Certain bacteria exhibit special resistance to specific physicochemical factors; therefore, the inoculated material can be treated with physicochemical methods to kill other microorganisms while preserving the desired bacteria, which can then be isolated and cultured.
In general, the test material can be isolated and cultured using the first two methods. If the test material is heavily contaminated, you can first treat it using the latter two methods and then use the first two methods to obtain a pure culture.
During the separation and culture procedure, strictly adhere to aseptic techniques. All instruments, culture media, and reagents must be sterilized and should not be exposed to air for extended periods. It is forbidden to touch the interior of sterilized containers with your hands or blow into them with your mouth.
Based on the characteristics of the potential pathogens present in the material being examined, select appropriate culture media and cultivation conditions (such as temperature and gas environment). For the initial isolation of unknown bacteria, it is best to use several different types of culture media, such as broth, blood agar, and MacConkey agar. Inoculate several tubes with each medium and incubate them separately under both aerobic and anaerobic conditions. Typically, results are observed after 24 to 78 hours; however, some pathogenic bacteria require much longer incubation periods to grow.
Generally, the test material does not require any pretreatment and can be directly inoculated onto the culture medium. When a pathogen suspected of producing spores is involved, the test material can be ground with physiological saline to prepare a 1:10 emulsion (no dilution is necessary for liquid materials). The emulsion should then be placed in a water bath at 60–80°C for 20–30 minutes to kill non-spore-forming contaminant bacteria before being inoculated onto the culture medium.
There are many methods for separating bacteria, and the following are some commonly used ones.
The material to be examined is inoculated onto a suitable culture medium, and then individual colonies growing on the surface of the solid medium are selected for isolation. These selected colonies are transferred to another suitable culture medium for further cultivation. Since a single colony typically originates from the growth and reproduction of a single bacterium, the bacteria cultivated in this way are of a single species—known as a pure culture.
Isolate bacteria using special culture environments (such as anaerobic or carbon dioxide environments, etc.).
The material to be tested is inoculated into susceptible animals, allowing the pathogenic bacteria to multiply within the animal body. Subsequently, samples are collected from the animals and subjected to centrifugation to separate and isolate the desired components, which are then cultured. Certain bacteria exhibit special resistance to specific physicochemical factors; therefore, the inoculated material can be treated with physicochemical methods to kill other microorganisms while preserving the desired bacteria, which can then be isolated and cultured.
In general, the test material can be isolated and cultured using the first two methods. If the test material is heavily contaminated, you can first treat it using the latter two methods and then use the first two methods to obtain a pure culture.
During the separation and culture procedure, strictly adhere to aseptic techniques. All instruments, culture media, and reagents must be sterilized and should not be exposed to air for extended periods. It is forbidden to touch the interior of sterilized containers with your hands or blow into them with your mouth.
Based on the characteristics of the potential pathogens present in the material being examined, select appropriate culture media and cultivation conditions (such as temperature and gas environment). For the initial isolation of unknown bacteria, it is best to use several different types of culture media, such as broth, blood agar, and MacConkey agar. Inoculate several tubes with each medium and incubate them separately under both aerobic and anaerobic conditions. Typically, results are observed after 24 to 78 hours; however, some pathogenic bacteria require much longer incubation periods to grow.
Generally, the test material does not require any pretreatment and can be directly inoculated onto the culture medium. When a pathogen suspected of producing spores is involved, the test material can be ground with physiological saline to prepare a 1:10 emulsion (no dilution is necessary for liquid materials). The emulsion should then be placed in a water bath at 60–80°C for 20–30 minutes to kill non-spore-forming contaminant bacteria before being inoculated onto the culture medium.