You have a “Centrifuge Gradient Guide” awaiting your receipt.

Release time:

2020-05-09


Overview:

When preparing a density gradient by centrifugation with a concave gradient, unlike a convex gradient, the heavier component of the gradient liquid flows into the centrifuge tube first from the mixing chamber. During preparation, the lighter component must be carefully layered on top slowly; therefore, the needle needs to be raised at an appropriate speed. However, in most cases, it is sufficient simply to tilt the centrifuge tube at a certain angle and gently place the needle at the tube’s opening, allowing the solution to flow down slowly along the tube wall and gradually spread out. After the entire gradient has been added, the centrifuge tube can then be placed upright for further processing.

  When Centrifuge When preparing a concave gradient, which is the opposite of a convex gradient, the heavier end of the gradient liquid flows first from the mixing chamber into the centrifuge tube. During preparation, the lighter liquid must be carefully layered on top slowly; therefore, the needle needs to be lifted at an appropriate rate. However, in most cases, it’s sufficient simply to tilt the centrifuge tube at a certain angle and gently place the needle at the tube’s opening, allowing the solution to flow down the tube wall gradually and evenly. After completing the layering, the centrifuge tube can then be placed upright for sample addition. At this point, it’s important to note that the material of the centrifuge tube used should ideally be hydrophilic. If using a hydrophobic centrifuge tube, adding a small amount of salt can help ensure that the gradient solution flows down uniformly when it’s introduced.

  To ensure the stability of the density gradient and sample bands, the density of the sample added to the top of the density gradient column must be lower than the density at the top of the gradient liquid. Otherwise, the sample will collapse through the gradient until it reaches the isopycnic zone. During this process, the sample layer will visibly expand, and the settling of entrained small droplets will lead to a deterioration in band resolution.

  The forms of centrifugal separation technology include centrifugal sedimentation, centrifugal filtration, centrifugal separation, and centrifugal analysis.

  1. Centrifugal Sedimentation: Separation is achieved based on the differing sedimentation rates of particles with varying sizes and densities in a centrifugal force field.

  2. Centrifugal Filtration: This process uses centrifugal force for separation, assisted by filter media.

  3. Centrifugal separation: Utilizing a gradient medium, this method leverages centrifugal force to separate particles with different densities and sedimentation coefficients.

  4. Centrifugal Analysis: Utilizing specialized rotors and detection methods to determine physical parameters such as particle density, molecular weight, and sedimentation coefficient.

  I. Selection of Gradient Media for Centrifuges:

  1. Salt gradient medium.

  2. Small-molecule organic compounds such as sucrose.

  3. Benzene derivatives of triiodide.

  4. Organic polymers.

  5. Colloidal silica.

  II. Density Range of Centrifuge Gradients:

  1. In rate-zonal centrifugation, the density of the medium is lower than the densities of the various particles in the sample.

  2. In density-gradient centrifugation, the density of the medium is greater than the densities of the various particles in the sample.

  3. Capacity of the centrifuge gradient:

  Refers to the maximum amount of sample that a gradient medium can accommodate, provided that the separation requirements are met.

  1. Related to the composition of the sample and separation requirements.

  2. It is related to the overall volume of the gradient, its slope, and the viscosity of the medium.

  3. It is related to the rotational speed and rotor configuration.

  Taking the gradient medium used in a refrigerated centrifuge as an example, we can summarize its key characteristics as follows: The gradient medium should be inert and at least non-toxic to the particles being separated. It is essential to understand the physicochemical properties of the gradient medium and to utilize one or more of these properties—such as refractive index—to determine the medium’s concentration. The gradient medium must be capable of quantitatively separating particles from the suspension; therefore, the gradient column prepared with this medium must have a well-defined density range. Within this specified density range, the gradient medium should be isotonic for particles sensitive to osmotic pressure. The gradient medium should be adjustable to a pH and ionic strength that closely match the physiological conditions of the particles being separated, and regardless of changes in the medium’s concentration, both the pH and ionic strength must remain constant and no hydration effects should occur. Within the given density range, the viscosity of the gradient medium should be as low as possible. Furthermore, the gradient medium must not interfere with the monitoring of sample bands during fractionation and separation.

  The gradient medium used in centrifuges should be easily removable from the separated particles without compromising the activity of the sample. It must be capable of being sterilized while maintaining its separation properties and not corroding the centrifuge tubes, rotors, or various measuring devices used. The gradient materials employed should be pure substances that are inexpensive; moreover, valuable materials should be readily recoverable and reusable after use.