The diffusion of a desktop centrifuge is unconditional and absolute.
Release time:
2015-10-19
Overview:
Desktop centrifuge
Desktop centrifuge When using this instrument, it is essential to ensure proper grounding for personal safety. Before using the instrument for the first time, please read the instruction manual carefully. The ideal operating temperature for a desktop centrifuge is between 0 and 40°C, with relative humidity below 80%. If the centrifuge is not used for an extended period, disconnect the power supply, plug in the power cord, and turn on the power switch. Place the samples to be separated into centrifuge tubes of equal weight, insert them into opposite centrifuge sleeves within the desktop centrifuge, close the lid, and then turn on the power. Adjust the desired centrifugal speed according to experimental requirements, and subsequently set the required centrifugation time or select the "normally closed" (0N) mode. This instrument is simple to operate, convenient to use, and delivers excellent centrifugation results. When a suspension containing fine particles is left undisturbed in a desktop centrifuge, the particles gradually settle downward under the influence of the gravitational field. The heavier the particles, the faster they sink; conversely, particles with lower density than the liquid will rise to the surface. The rate at which particles move under gravity depends on their size, shape, and density, as well as on the strength of the gravitational field and the viscosity of the liquid. Particles about the size of red blood cells—typically several micrometers in diameter—can be observed undergoing sedimentation even under normal gravitational conditions.
Moreover, as particles settle in a medium, they are accompanied by the phenomenon of diffusion. Diffusion is unconditional and absolute. It is inversely proportional to the mass of the substance—thus, the smaller the particles, the more severe the diffusion. In contrast, sedimentation is relative and conditional; it requires external forces to initiate motion. Sedimentation is directly proportional to the weight of the object—hence, the larger the particles, the faster they settle. For particles smaller than a few micrometers—such as viruses or proteins—when these particles are dispersed in a solution, they exist in a colloidal or semi-colloidal state. Under such circumstances, it is simply impossible to observe the sedimentation process using only gravity with a benchtop centrifuge. This is because the smaller the particles, the slower their sedimentation rate becomes, while the diffusion phenomenon becomes increasingly pronounced. Therefore, it is necessary to employ a centrifuge that generates a powerful centrifugal force to overcome diffusion and induce sedimentation in these tiny particles. Select... Desktop centrifuge A comprehensive analysis must be conducted based on factors such as the size and concentration of solid particles in the suspension (or emulsion), the density difference between the solid phase and the liquid phase (or between two liquids), the viscosity of the liquid, the characteristics of the filter cake (or sediment), and the specific separation requirements. This analysis will help determine the appropriate type of benchtop centrifuge to use, ensuring that the moisture content of the filter cake (sediment) and the clarity of the filtrate (separated liquid) meet the required standards. Subsequently, the centrifuge model and specifications are selected according to the processing capacity and the level of automation required for operation, and finally, the selection is validated through actual testing.
The desktop centrifuge features a variable-frequency motor, an environmentally friendly fluorine-free compressor, a fully automatic locking door lid with an alarm system, a 32-bit ARM microprocessor, and a wide-angle LCD display. It is equipped with a CAN RS485 interface, enabling network connectivity between the computer and the horizontal screw centrifuge. The centrifuge boasts rotor recognition functionality and incorporates 32 sets of program storage with integrated W2dt display and control capabilities, allowing for stepwise separation. In its rotating system, a spring-cone assembly is used for rotor installation and removal, ensuring high repeatability and ease of rotor handling, thereby enhancing the consistency and accuracy of the separation process.
Desktop centrifuges are widely used in fields such as bioengineering, hospitals, education, scientific research, blood banks, agriculture, and environmental protection. Changsha Intech Instruments Co., Ltd. and Changsha Pingfan Instruments Co., Ltd. have stepped up their R&D efforts and are working hard to develop new desktop centrifuge products, thereby elevating China’s desktop centrifuge technology to a new level. The newly developed desktop centrifuges boast key technical specifications that have reached the internationally advanced level of similar products, and both their process technology and appearance have been significantly improved.
Due to the action of centrifugal force, particles in a benchtop centrifuge separate from the original sample layer and begin to sediment toward the bottom of the tube at different rates. After centrifuging for a certain period, the settled particles gradually separate from one another, eventually forming a series of distinct, discontinuous bands with clear interfaces. The larger the sedimentation coefficient, the faster the particles will sink, and the lower the corresponding band will appear. Centrifugation must be terminated before the largest particles, which sediment fastest, reach the bottom of the tube. The density of the sample particles must be greater than that of the gradient medium. The gradient medium is typically a sucrose solution. Desktop centrifuge The maximum density and concentration can reach 1.28 kg/cm³ and 60%, respectively.
Moreover, as particles settle in a medium, they are accompanied by the phenomenon of diffusion. Diffusion is unconditional and absolute. It is inversely proportional to the mass of the substance—thus, the smaller the particles, the more severe the diffusion. In contrast, sedimentation is relative and conditional; it requires external forces to initiate motion. Sedimentation is directly proportional to the weight of the object—hence, the larger the particles, the faster they settle. For particles smaller than a few micrometers—such as viruses or proteins—when these particles are dispersed in a solution, they exist in a colloidal or semi-colloidal state. Under such circumstances, it is simply impossible to observe the sedimentation process using only gravity with a benchtop centrifuge. This is because the smaller the particles, the slower their sedimentation rate becomes, while the diffusion phenomenon becomes increasingly pronounced. Therefore, it is necessary to employ a centrifuge that generates a powerful centrifugal force to overcome diffusion and induce sedimentation in these tiny particles. Select... Desktop centrifuge A comprehensive analysis must be conducted based on factors such as the size and concentration of solid particles in the suspension (or emulsion), the density difference between the solid phase and the liquid phase (or between two liquids), the viscosity of the liquid, the characteristics of the filter cake (or sediment), and the specific separation requirements. This analysis will help determine the appropriate type of benchtop centrifuge to use, ensuring that the moisture content of the filter cake (sediment) and the clarity of the filtrate (separated liquid) meet the required standards. Subsequently, the centrifuge model and specifications are selected according to the processing capacity and the level of automation required for operation, and finally, the selection is validated through actual testing.
The desktop centrifuge features a variable-frequency motor, an environmentally friendly fluorine-free compressor, a fully automatic locking door lid with an alarm system, a 32-bit ARM microprocessor, and a wide-angle LCD display. It is equipped with a CAN RS485 interface, enabling network connectivity between the computer and the horizontal screw centrifuge. The centrifuge boasts rotor recognition functionality and incorporates 32 sets of program storage with integrated W2dt display and control capabilities, allowing for stepwise separation. In its rotating system, a spring-cone assembly is used for rotor installation and removal, ensuring high repeatability and ease of rotor handling, thereby enhancing the consistency and accuracy of the separation process.
Desktop centrifuges are widely used in fields such as bioengineering, hospitals, education, scientific research, blood banks, agriculture, and environmental protection. Changsha Intech Instruments Co., Ltd. and Changsha Pingfan Instruments Co., Ltd. have stepped up their R&D efforts and are working hard to develop new desktop centrifuge products, thereby elevating China’s desktop centrifuge technology to a new level. The newly developed desktop centrifuges boast key technical specifications that have reached the internationally advanced level of similar products, and both their process technology and appearance have been significantly improved.
Due to the action of centrifugal force, particles in a benchtop centrifuge separate from the original sample layer and begin to sediment toward the bottom of the tube at different rates. After centrifuging for a certain period, the settled particles gradually separate from one another, eventually forming a series of distinct, discontinuous bands with clear interfaces. The larger the sedimentation coefficient, the faster the particles will sink, and the lower the corresponding band will appear. Centrifugation must be terminated before the largest particles, which sediment fastest, reach the bottom of the tube. The density of the sample particles must be greater than that of the gradient medium. The gradient medium is typically a sucrose solution. Desktop centrifuge The maximum density and concentration can reach 1.28 kg/cm³ and 60%, respectively.