Supplement to the Basic Content on Safe Operation of Centrifuges
Release time:
2015-02-28
Overview:
The laboratory and production environments constantly remind us that, at present, accidents involving centrifugation experiments due to improper operation occur from time to time. Therefore, it is essential to cultivate awareness of safe centrifuge operation.
The laboratory and production safety constantly remind us that, at present, accidents during centrifugation experiments caused by improper operation occur from time to time. Therefore, it is essential to perform operations safely. Centrifuge Cultivating awareness is essential. The article recently published on “How to Properly Use Centrifuge Rotors” can also be considered part of the foundational content for safe centrifuge operation. Below, we’ll provide additional information on the fundamentals of safe centrifuge operation.
(1) Precisely balance the centrifuge tube and its contents.
1. Balancing Centrifuge Tubes and Their Contents: When using various centrifuges, it is essential to precisely balance all centrifuge tubes, tube holders, caps and top covers, shields, and tube sleeves on a balance beforehand. The weight difference during balancing must not exceed the range specified in the instruction manual for each particular centrifuge. Tube sleeves and shields are usually labeled with their weights; be careful not to mix up matching tube sleeves and shields during the balancing process. The tubes must be filled with materials that are similar to those intended for centrifugation—for example, when centrifuging bacteria from a culture medium, you can use a balanced solution of the same medium. However, you must never use water to balance tubes containing cesium chloride.
2. Symmetrical loading of centrifuge tubes: It is strictly forbidden to load an odd number of centrifuge tubes into the rotor. When the rotor is only partially loaded, place the tubes in a way that ensures the load is evenly distributed around the rotor.
(2) Proper amount of solution to be loaded: When loading the solution, it is necessary to consider various factors. Centrifuge Follow the specific operating instructions. Select an appropriate centrifuge tube based on the properties and volume of the solution to be centrifuged. Some centrifuge tubes do not have lids; therefore, do not fill them too much, as this could cause the liquid to splash out during centrifugation, leading to rotor imbalance, rusting, or corrosion. For ultracentrifuge tubes used in preparing samples, it is often required to fill them completely to prevent the upper part of the plastic centrifuge tubes from collapsing and deforming during centrifugation.
(3) Ensure the lid is securely closed before starting: Before initiating the centrifuge, always remember to close the chamber door, the lid, and the rotor cover tightly. After starting the centrifuge, the operator must not leave the machine until the rotation speed has reached the preset value and the operation has stabilized. However, the operator should continue to monitor the running condition at all times. During operation, if any abnormal situation occurs, immediately stop the centrifuge and take appropriate corrective action. In the event of a sudden power failure during operation, you must first disconnect the power supply and wait for the rotor to gradually slow down due to inertia. Once it has come to a complete stop, manually open the chamber door of the centrifuge and remove the samples and rotor.
(4) Remove the centrifuge tubes promptly: Immediately after the centrifugation is complete, from... Centrifuge Remove the centrifuge tube from the centrifuge, immediately wash the tube after transferring its contents, and allow the tube to air-dry naturally.
(5) Clean the rotor promptly: After centrifugation is complete, the rotor should be washed with warm water and dried. Generally, rinsing with water alone is sufficient; never soak the rotor in detergents. Once cleaned, dry the rotor thoroughly and allow it to air-dry in a clean, dry environment. If the rotor will not be used for an extended period, apply a layer of polishing wax for protection.
(1) Precisely balance the centrifuge tube and its contents.
1. Balancing Centrifuge Tubes and Their Contents: When using various centrifuges, it is essential to precisely balance all centrifuge tubes, tube holders, caps and top covers, shields, and tube sleeves on a balance beforehand. The weight difference during balancing must not exceed the range specified in the instruction manual for each particular centrifuge. Tube sleeves and shields are usually labeled with their weights; be careful not to mix up matching tube sleeves and shields during the balancing process. The tubes must be filled with materials that are similar to those intended for centrifugation—for example, when centrifuging bacteria from a culture medium, you can use a balanced solution of the same medium. However, you must never use water to balance tubes containing cesium chloride.
2. Symmetrical loading of centrifuge tubes: It is strictly forbidden to load an odd number of centrifuge tubes into the rotor. When the rotor is only partially loaded, place the tubes in a way that ensures the load is evenly distributed around the rotor.
(2) Proper amount of solution to be loaded: When loading the solution, it is necessary to consider various factors. Centrifuge Follow the specific operating instructions. Select an appropriate centrifuge tube based on the properties and volume of the solution to be centrifuged. Some centrifuge tubes do not have lids; therefore, do not fill them too much, as this could cause the liquid to splash out during centrifugation, leading to rotor imbalance, rusting, or corrosion. For ultracentrifuge tubes used in preparing samples, it is often required to fill them completely to prevent the upper part of the plastic centrifuge tubes from collapsing and deforming during centrifugation.
(3) Ensure the lid is securely closed before starting: Before initiating the centrifuge, always remember to close the chamber door, the lid, and the rotor cover tightly. After starting the centrifuge, the operator must not leave the machine until the rotation speed has reached the preset value and the operation has stabilized. However, the operator should continue to monitor the running condition at all times. During operation, if any abnormal situation occurs, immediately stop the centrifuge and take appropriate corrective action. In the event of a sudden power failure during operation, you must first disconnect the power supply and wait for the rotor to gradually slow down due to inertia. Once it has come to a complete stop, manually open the chamber door of the centrifuge and remove the samples and rotor.
(4) Remove the centrifuge tubes promptly: Immediately after the centrifugation is complete, from... Centrifuge Remove the centrifuge tube from the centrifuge, immediately wash the tube after transferring its contents, and allow the tube to air-dry naturally.
(5) Clean the rotor promptly: After centrifugation is complete, the rotor should be washed with warm water and dried. Generally, rinsing with water alone is sufficient; never soak the rotor in detergents. Once cleaned, dry the rotor thoroughly and allow it to air-dry in a clean, dry environment. If the rotor will not be used for an extended period, apply a layer of polishing wax for protection.