There’s a knack to using a centrifuge—this is how you ensure it lasts a long time.
Release time:
2020-05-06
Overview:
Centrifuge When operating, speed is key—especially with high-speed centrifuges—so safety considerations must be taken extremely seriously.
Anyone who has ever worked with a centrifuge knows that it’s not only an “expensive piece of equipment” but also a “fussy one.” Therefore, when using a centrifuge, you should pay attention to the following points:
1. When the centrifuge is in the pre-cooling state, the centrifuge lid must be closed. After the centrifugation is complete, once the rotor is removed, it should be inverted onto the experimental bench, and any remaining water inside the chamber should be wiped dry. The centrifuge lid should remain open.
2. Turn on the centrifuge once a week and run it at low speed with a rotor installed to ensure its proper functioning.
3. Regularly use a level to check whether the centrifugal shaft or centrifugal housing is horizontal. If it’s not level, adjustments must be made.
4. After each use of the centrifuge, the rotor must be removed immediately.
5. Regularly change the oil in the vacuum pump and diffusion pump to ensure the vacuum system operates properly.
6. Each time the centrifuge is used, detailed records must be kept, and a yearly statistical summary must be prepared. For high-speed centrifuges, both the entire machine and the rotor used have a specified service life. The entire machine is warranted for 16 billion revolutions; aluminum rotors can be used for 1,000 cycles or 2,500 hours, while titanium rotors can be used for 5,000 cycles or 10,000 hours. If the service life is reached, the centrifuge must be operated at a lower speed or with reduced capacity.
7. The main accessories of a centrifuge include rotors and centrifuge tubes, among others. When using these accessories, you must strictly follow the instructions provided in their manuals. In daily use, pay close attention to their cleaning, disinfection, and maintenance. If you notice any obvious cracks at the bottom of the rotor’s centrifugal holes or at the bottom or walls of the centrifuge tubes, do not use them.
8. Rotors from different manufacturers cannot be mixed and should be used in pairs; otherwise, the rotor’s lifespan will be shortened, and the centrifuge could even be damaged.
9. As long as the centrifuge is carefully maintained, its operating status is closely monitored, its sounds are listened to, early diagnosis is performed, and any issues are addressed promptly, the centrifuge can operate at peak efficiency.
If you can achieve the nine points mentioned above when using a centrifuge, ensuring its longevity will no longer be a challenge. Of course, proper usage must be accompanied by meticulous maintenance. While the ninth point was only briefly touched upon earlier, below we’ll provide a detailed explanation of how to properly maintain your centrifuge:
Before starting the centrifuge, first disconnect the power supply and release the centrifuge brake. You can manually rotate the drum to check for any binding or jamming. Also, inspect other parts for looseness or unusual conditions.
Connect the power supply and start the machine by turning the knob clockwise (typically, it takes about 40 to 60 seconds from a standstill to normal operation). Usually, after each piece of equipment is delivered to the factory, it should be run empty for about 3 hours. It can begin working once no abnormalities are detected. Materials should be placed as evenly as possible.
The centrifuge must be operated by a dedicated person, and its capacity must not exceed the rated limit. It is strictly forbidden to run the machine at speeds higher than its rated capacity, as this could shorten the machine’s service life. After starting the machine, if any abnormal conditions are detected, the machine must be stopped immediately for inspection; if necessary, it should be disassembled, cleaned, and repaired. During operation, the centrifuge runs at high speed; therefore, never touch its rotating drum with your body to avoid accidents. The mesh size of the filter cloth should be selected according to the particle size of the solid phase in the material being separated; otherwise, the separation efficiency will be compromised. Additionally, when installing the filter cloth, make sure to snap the sealing ring of the filter cloth into the sealing groove of the rotating drum to prevent material from leaking in.
To ensure the centrifuge operates properly, lubricate and maintain the rotating components every six months. At the same time, check the lubrication condition at the bearings for any signs of wear; inspect the components in the braking system for wear, and replace any severely worn parts. Also, verify that there are no oil leaks from the bearing covers. After use, be sure to clean the centrifuge thoroughly and keep it tidy. Do not use non-corrosion-resistant centrifuges for separating highly corrosive materials. In addition, always operate the equipment strictly according to its requirements and regulations; never use non-explosion-proof centrifuges in flammable or explosive environments.
Finally, it’s important to remind you that when loading solutions into a centrifuge, you must follow the specific operating instructions for each type of centrifuge. Select appropriate centrifuge tubes based on the properties and volume of the liquid to be centrifuged. Some centrifuge tubes are open-top; in such cases, do not fill them too much, as overfilling could cause the liquid to splash out during centrifugation, leading to imbalance, rusting, or corrosion of the rotor. For preparative ultracentrifuge tubes, however, it is often required to fill them completely to prevent the upper part of the plastic tube from collapsing and deforming during centrifugation. After each use, be sure to carefully inspect the rotor, promptly clean and dry it thoroughly. The rotor is a critical component of the centrifuge that requires special protection. Handle it with care during transport—avoid any impacts or collisions that could cause scratches or damage. If the rotor will not be used for an extended period, apply a thin layer of polishing wax for protection. Under no circumstances should you use centrifuge tubes that show significant deformation, damage, or signs of aging.
Previous: