Understand the Prevention Knowledge for Common Issues with High-Speed Centrifuges in Three Minutes

Release time:

2018-12-05


Overview:

Problems commonly encountered when operating high-speed centrifuges on a daily basis—some of these issues can actually be prevented by ourselves. However, this is just one person’s perspective, so I hope everyone will share their thoughts and experiences more often.

Did you know? High-speed centrifuge Common problems can now be prevented!

  High-speed centrifuges represent a broad category that can be expanded into many new models with additional features, such as high-speed refrigerated centrifuges, benchtop high-speed refrigerated centrifuges, and high-speed microcentrifuges, among others!

  However, no matter how much the product may vary, its core feature remains “high speed”—this product is all about speed! The second important factor is capacity. This depends on the user’s needs—after all, some studies require large capacities, while others only need tiny amounts!

  Next, let me share with you some common issues encountered when operating high-speed centrifuges on a daily basis. While some of these issues can be prevented by ourselves, they’re ultimately just one person’s perspective—so I hope everyone will join in and share their own experiences!

  Common Issue 1: The temperature fails to reach the set requirement.

  1) If it hasn't been pre-cooled or hasn't been pre-cooled sufficiently, ensure it's fully pre-cooled.

  2) If the control valve is damaged, replace it.

  3) If the compressor is damaged, replace it.

  4) If the refrigerant level is insufficient, add an appropriate amount of refrigerant.

  Common Issue No. 2: The centrifuge has significant vibration;

  1) If the centrifuge tubes inside the rotor are not placed symmetrically, check and adjust them accordingly.

  2) If the centrifuge tube breaks, inspect and replace it.

  3) If the rotor is not tightened, check and adjust it.

  4) If the shock-absorbing mechanism is damaged, inspect and replace it.

  Common Issue 3: The display shows that the high-speed centrifuge does not start when the start button is pressed.

  1) If the control system plug is loose, reinsert it firmly.

  2) If the motor is damaged, replace it.

  3) If the button is damaged, replace it.

  4) If the circuit board or transformer is damaged, replace it.

  Common Problem 4: The centrifuge can run but fails to reach the desired speed, and it emits unusual noises or odors.

  1) If the control system or motor malfunctions, inspect and repair it.

  (4) Fault phenomenon: The actual speed differs from the set or displayed speed, resulting in loss of control or instability.

  1) If the control system malfunctions, inspect and repair it.

  FAQ 5: Troubleshooting and Repair of Safety Protection Systems:

  (1) Overtemperature: Check whether the compressor is functioning properly, whether the temperature sensor socket on the control board is loose, whether the temperature sensor is damaged, whether the temperature-control solenoid valve socket is loose, and whether the temperature-control solenoid valve itself is damaged.

  (2) Door Open: Confirm that the door cover is securely closed; check whether the door cover status socket on the control panel is loose and whether the door cover detection switch is damaged, etc.

  (3) Imbalance: Check whether the weight of the separated sample in the centrifuge chamber is within the specified range and whether the imbalance socket on the control panel is loose, etc.;

  (4) Over-speed: Check whether the speed sensor socket on the control board is loose and whether the speed sensor itself is damaged;

  Frequently Asked Question 6: Common Troubleshooting and Repair:

  (1) Fault phenomenon: The display screen does not light up after the power cord is plugged in.

  1) If there is no power, check the power supply.

  2) If the fuse blows, inspect and replace it.

  3) If the connector at the communication signal input is loose, check and adjust it.

  Alright, given space constraints, that’s all for today’s sharing from the editor. We hope more users of high-speed centrifuges will join the conversation and share their experiences—let’s all keep learning and improving together!