Experimental Procedure for Rapid Extraction of Tissue/Cell RNA Using a High-Speed Centrifuge

Release time:

2014-10-27


Overview:

Centrifuge the lysate at 13,000 rpm for 3 minutes after homogenization to pellet any fragments that may be difficult to lyse or insoluble materials. Carefully transfer the supernatant from the lysate into a new centrifuge tube.

Tip:
 Before first use, please add the specified amount of anhydrous ethanol to both the rinse solution RW bottle and the 70% ethanol bottle!
 Before operation, add β-mercaptoethanol to the lysis buffer RLT to a final concentration of 1%. For example, add 10 μl of β-mercaptoethanol to 1 ml of RLT. It is best to prepare this lysis buffer fresh just before use. The prepared RLT can be stored at 4°C for up to one month.

1. Tissue culture cells
a. Collect fewer than 107 suspended cells into a 1.5 ml centrifuge tube. For adherent cells, if cultured in a cell culture plate, you can directly lyse the cells in the plate; for cells cultured in flasks, first digest them with trypsin and then gently pipette them out for collection.

b. Centrifuge at 13,000 rpm for 10 seconds (or at 300g for 5 minutes) to pellet the cells. Carefully aspirate the supernatant completely, leaving behind the cell pellet. Be aware that incomplete removal of the supernatant may dilute the lysis buffer, thereby reducing the yield and purity.

c. Gently tap the tube wall to completely resuspend and disperse the cell pellet. Add 350 μl (for <5×10⁶ cells) or 600 μl (for 5×10⁶–1×10⁷ cells) of RLT lysis buffer, mix thoroughly by pipetting, and then vigorously shake by hand for 20 seconds to ensure complete lysis.

d. Use a disposable 1 ml syringe with a blunt needle (equipped with a 0.9 mm needle) to gently pipette the lysate 5–10 times, or until a satisfactory homogenization result is achieved (or use an electric homogenizer for 30 seconds). This process can shear DNA, reduce viscosity, and increase yield.

e. Under the operation steps, item 3.


2. Animal tissues (e.g., mouse liver and brain)
a. Electric homogenization: Fresh tissue is quickly cut into small pieces using a surgical blade, then 350 μl (<20 mg tissue) or 600 μl (20–30 mg tissue) of RLT lysis buffer is added. The tissue is thoroughly homogenized electrically for 20–40 seconds.

b. Liquid Nitrogen Grinding + Homogenization: After grinding the tissue into a fine powder in liquid nitrogen, transfer an appropriate amount of tissue powder (20 mg/30 mg) into a 1.5 ml centrifuge tube containing 350 μl/600 μl of RLT tissue lysis buffer. Vigorously shake by hand for 20 seconds to ensure thorough lysis. Use a disposable 1 ml syringe equipped with a blunt needle (with a 0.9 mm needle) to pipette the lysate up and down 10 times, or until a satisfactory homogenized result is achieved (alternatively, use an electric homogenizer for 30 seconds). This step helps shear DNA, reduce viscosity, and increase yield.

c. Centrifuge the lysate at 13,000 rpm for 3 minutes after homogenization to pellet any poorly lysed fragments or insoluble materials. Carefully transfer the supernatant from the lysate into a new centrifuge tube.

d. See operation step item 3.


3. Accurately estimate the volume of the lysate (supernatant), then add an equal volume of 70% ethanol (please first check whether anhydrous ethanol has already been added!). At this point, a precipitate may form, but this does not affect the extraction process. Immediately pipette up and down to mix thoroughly—do not centrifuge.


4. Immediately add the mixture (less than 700 μl each time; if necessary, you can divide it into two portions) to an adsorption column RA (place the adsorption column into a collection tube). Centrifuge at 13,000 rpm for 60 seconds, then discard the waste liquid.


5. Add 700 μl of protein removal solution RW1, let it stand at room temperature for 30 seconds, then centrifuge at 12,000 rpm for 30 seconds and discard the supernatant. If significant DNA residue remains, you can let it stand at room temperature for 5 minutes after adding RW1 before centrifuging again.


6. Add 500 μl of wash solution RW (please first check whether anhydrous ethanol has been added!). Centrifuge at 12,000 rpm for 30 seconds, then discard the supernatant. Add another 500 μl of wash solution RW and repeat the step.


7. Place the adsorption column RA back into the empty collection tube, and centrifuge at 13,000 rpm for 2 minutes to remove as much of the wash solution as possible, ensuring that no residual ethanol from the wash solution remains, which could inhibit downstream reactions.


8. Remove the adsorption column RA and place it into an RNase-free centrifuge tube. According to the expected RNA yield, add 30–50 μl of RNase-free water to the middle portion of the adsorption membrane (preheating the water in a 70–90℃ water bath can enhance the yield). Allow it to stand at room temperature for 1 minute, then centrifuge at 12,000 rpm for 1 minute.


9. If the expected RNA yield exceeds 30 μg, add 30–50 μl of RNase-free water and repeat Step 8. Combine the eluates from both washes, or alternatively, use the first eluate and return it to the adsorption column for another round of washing (if a higher RNA concentration is required). The RNA eluate obtained after two rounds of washing has a higher concentration; combining the eluates from two separate washes results in an RNA yield that is 15–30% higher than that obtained from a single wash. However, the concentration will be lower. Users should choose based on their specific needs.