Analysis of the Role of Laboratory Centrifuges in Protein Expression Systems

Release time:

2021-12-27


Overview:

In studies related to protein expression, centrifuges play an important role. There are four major systems for in vitro recombinant protein expression: the Escherichia coli expression system, mammalian cell expression, yeast expression system, and insect cell expression.

  As can be seen in studies related to protein expression, Centrifuge Played an important role.

  There are four major systems for in vitro recombinant protein expression: the E. coli expression system, mammalian cell expression, yeast expression system, and insect cell expression.

  Today, we’re going to go into detail about the E. coli expression system.

  Let’s start by understanding the steps involved in the E. coli expression system:

  Excluding upstream operations such as gene construction and the protein purification step. Gene construction refers to codon optimization, while protein purification refers to the specialized topic of protein purification. The following content primarily focuses on the identification of protein expression:

  On the first day of plasmid identification, we perform resistance selection using competent cells to obtain the plasmid. The laboratory centrifuge is used to spin the mixture at 3,000 rpm for 2 minutes. Next, TE buffer is added to the plasmid solution (so that the final amount of plasmid added to 110 μL of competent cells will be 80–100 ng; based on this, the appropriate volume of TE buffer to add is determined). Typically: (1 μg plasmid plus 20 μL TE; 2 μg plasmid plus 50 μL TE; 5 μg plasmid plus 100 μL TE). After thoroughly mixing the plasmid with TE, 2 μL of the resulting mixture is added to the competent cells. The competent cells are then placed in a refrigerator (4℃) for 30 minutes. After 30 minutes, they are immediately transferred to a water bath set at 42℃ and subjected to heat shock for 90 seconds. The cells are then returned to the refrigerator (4℃) for 3 minutes. Following this, 200 μL of LB liquid medium is added to the competent cells that have been transformed with the plasmid, and the mixture is incubated on a shaker (37℃; 195 rpm) for 30 to 60 minutes—ideally for 45 minutes. After incubation, the mixture is centrifuged at 3,000 rpm for 2 minutes. The supernatant (200 μL) is carefully removed, leaving approximately 100 μL of supernatant to resuspend the cell pellet. Then, 50 μL of the resuspended cells are spread onto an agar plate. (First, the plates corresponding to the specific antibiotic resistance are placed in the incubator (37℃) and preheated for 20 minutes.) The plates are subsequently placed back into the incubator (37℃) and left overnight (12 to 16 hours).

  Next, specify the task for the next day’s identification. Pay attention to the expression temperature of Pcold:

  Pick a single colony from each plate and transfer it into four L-tubes (4 ml) corresponding to the respective resistance markers, labeled “0,” “1,” “2,” and “3.”

  Place the test tubes into a shaker (37℃; 195 rpm). For single antibodies, incubate for about 3 hours; for double antibodies, incubate for about 4 hours. Initially, use a visible spectrophotometer to measure the OD value; once you become proficient, you can estimate visually (with backlighting—taking the pipette tip in the tube as an example, just start noticing that the tip becomes invisible). Measure the OD value (between 0.6 and 0.8).

  Take 700 μL of the suspension from tube No. 0 and add it to 100 μL of cryopreservation glycerol (80% concentration). Mix thoroughly, then store in a freezer (-20℃) for long-term preservation.

  Add 2 μL of IPTG (with a final concentration of 0.5 mM, the optimal concentration) to tubes numbered “1,” “2,” and “3” in each bacterial group.

  Depending on the vector used, select an appropriate expression environment: (PET/PGEX: Express overnight at 15℃; express for 6 hours at 25℃; express for 3 to 4 hours at 37℃—four tubes in total: tubes “0” and “1” express overnight at 15℃; tubes “2” and “3” express for 3 to 4 hours at 37℃). Pcold: All samples express overnight at 15℃.

  Finally, on the third day of expression and identification, perform an analysis of whole-cell expression and identification. Pay attention to controlling the amount of solute and the viscosity of the solution:

  From each group of four test tubes, pipette 500 μL of bacterial suspension into a 1.5 ml centrifuge tube. (If the OD values differ, take a larger volume for the tube with the lower OD.) Centrifuge at 6,000 rpm for 5 minutes, discard the supernatant, and retain the pellet. (If the pellet is small, you can re-pipette some bacterial suspension and centrifuge again, aiming to obtain a pellet volume that is as close as possible to the others.)

  Add 500 μL of DDH2O to each centrifuge tube, resuspend the precipitate, and centrifuge at 6,000 r/min for 5 minutes. Discard the supernatant and retain the precipitate.

  Add 45 μL of 1× PBS and 45 μL of 2× Loading Buffer to each centrifuge tube to resuspend the precipitate. (If the solute is present in appropriate and uniform amounts, the addition volumes remain unchanged; however, if the solute is abundant and viscous, the addition volumes should be increased. To reduce viscosity, you can also decrease the volume of the supernatant.)

  Place in the cooking apparatus (100℃) for 25 minutes.

  After removal, centrifuge at 6000 rpm for 3 minutes, then perform electrophoresis for detection.

  As can be seen from the detailed steps above, the laboratory centrifuge is indispensable throughout the entire process.