The Application of Centrifuges in Quiescent Cell Reaction Experiments

Release time:

2021-12-17


Overview:

The smooth execution of the cell response inhibition experiment requires a centrifuge, as centrifugation is used to separate and extract cells during the bacterial collection stage of cell preparation.

  The smooth execution of the cell response inhibition experiment requires Centrifuge 。

  Because during the cell preparation stage, cells are collected through centrifugation to separate and extract them.

  Quiescent cells, also known as resting cells, are obtained by washing away various nutrients and growth factors from the culture medium and then suspending them in physiological saline for a period of time. This process depletes the cells of their endogenous nutrients, placing them in a state of starvation. Quiescent cells find wide application in the study of microbial physiology, biochemistry, and metabolism. Their key characteristic is that although these cells are in a dormant state and do not undergo growth or reproduction, they still contain a variety of enzymatic systems and retain both oxidative and fermentative capabilities. Under suitable conditions, they can resume growth. Moreover, quiescent cells exhibit highly specific responses, which can enhance substrate conversion rates, reduce the likelihood of contamination by extraneous microorganisms, and minimize the inhibitory effects of the product on cell growth and enzyme synthesis.

  Preparation of quiescent cells:

  (1) Strain activation

  Using an inoculation loop, inoculate the E. coli CVCC 249 strain required for the experiment onto a sterilized solid slant medium, and incubate at 37 ℃ for 18–24 hours.

  (2) Acquisition of the strain

  Using an inoculation loop, scrape an appropriate amount of bacteria from the slant culture medium and transfer it into a liquid Erlenmeyer flask. Incubate in a constant-temperature shaker at 37 ℃ until the OD exceeds 1 (approximately around 1.4).

  (3) Collection of bacteria

  Transfer the cultured cell suspension into a centrifuge tube, and centrifuge at 4,500 rpm to collect the cells. Discard the supernatant culture medium, then wash the cells with physiological saline to remove any residual culture medium. Next, centrifuge again at 4,500 rpm to collect the cells. Repeat the washing process three times until the supernatant becomes clear, then discard the supernatant.

  (4) Preparation of the bacterial suspension

  Quantify the centrifuged cells to 25 mL using phosphate-buffered saline at pH 7.0, then gently pipette up and down to ensure uniform suspension for subsequent experiments.

  (5) Preparation of quiescent cells

  After the bacterial suspension has been stored at 4 ℃ for 72 hours, it is incubated at 37 ℃ for 4–8 hours to prepare stationary-phase cells, which are then stored in a 4 ℃ refrigerator for later use.

  Determination of dehydrogenase activity:

  (1) Add 1 mL of reaction substrate to a 5-mL centrifuge tube, and set different concentrations according to the substrate (the effect of different substrates at the same concentration on cellular dehydrogenase activity is shown in Table 1; the effects of various substrates at different dilutions on bacterial dehydrogenase activity were studied using three substrates—sodium acetate, sodium succinate, and sodium citrate—as shown in Tables 2, 3, and 4).

  (2) Add 0.4 mL of the prepared quiescent cells, and use an equal volume of 5% formaldehyde-treated cell suspension that has been inactivated for 30 minutes as a control. Be sure to gently shake the quiescent cells before adding them.

  (3) Add 40 μL of MTT, shake gently to mix thoroughly. The resulting solution should be yellow. Incubate in a constant-temperature incubator at 37 ℃, protected from light, for 2 hours.

  (4) Add 1.3 mL of dimethyl sulfoxide, shake thoroughly to mix, and then incubate at 37 ℃ for 30 minutes. At this point, the solution will turn a deep blue-purple color.

  (5) Add 1.5 mL of PBS (pH 7.0) and shake to mix thoroughly.

  (6) Use a 722 spectrophotometer to measure OD at 510 nm. For each sample concentration, conduct at least three replicate experiments, with a coefficient of variation (CV) less than 5%.

  Enzyme activity refers to the ability of an enzyme to catalyze a specific chemical reaction. Every enzyme has the capacity to catalyze a particular reaction involving specific substrates; however, the measurement of an enzyme's catalytic activity can actually be carried out only by determining the rate at which the enzyme catalyzes the reaction. The greater the reaction rate catalyzed by an enzyme, the higher its activity; conversely, the lower the reaction rate, the lower its activity. The rate of an enzymatic reaction can be expressed as the amount of substrate consumed or the amount of product formed per unit time and per unit volume. In addition, when studying enzymatic reactions, the substrate is usually present in excess; therefore, it is generally more appropriate to measure the increase in product concentration. Since the rate of an enzymatic reaction is influenced by numerous factors—including temperature, pH, ionic strength, and substrate concentration—we refer to enzyme activity as the reaction rate measured under specific system and condition parameters. Consequently, when determining enzyme activity, it is essential to clearly specify these particular conditions. Even for the same enzyme, or even when using the same assay method and the same unit definitions, slight differences in experimental conditions can make it difficult to compare the measured enzyme activities directly. Therefore, when comparing enzyme activities reported in different publications or in preparations from different brands, it is crucial to pay close attention to their respective unit definitions, assay systems, and experimental conditions—never attempt to make comparisons without first ensuring that these factors have been carefully accounted for.

  Another concept related to enzyme activity is “specific activity,” which refers to the catalytic activity of a particular enzyme per unit weight of protein. It serves as a measure of purity and is expressed in units of U/mg. The higher the specific activity, the purer the enzyme.