A well-maintained environment is fundamental to the proper operation of a centrifuge.

Release time:

2018-12-10


Overview:

The operating environment for a centrifuge has certain requirements: First, the temperature must not be too extreme; second, the placement surface must be stable; and finally, there’s the voltage!

   Centrifuge The operating environment has certain requirements: First, the temperature must not be too extreme; second, the placement surface must be stable; and finally, there’s the voltage!


  Especially in spaces that are constantly on the move—such as certain vehicles—common examples include blood donation vehicles, which also require centrifuges. To be more specific in this context:


  Vacuum and refill the crankcase of the data center air-conditioning unit. First, close the liquid supply valve and the suction valve. Once the crankcase pressure drops slightly below atmospheric pressure, open the refilling valve; under atmospheric pressure, oil will flow into the crankcase through the refilling valve. When the oil level reaches the required level, close the refilling valve, then gradually open the compressor’s suction valve and the associated liquid supply valve to resume normal operation. Use a dedicated oil pump for data center air-conditioning units to add oil. When the compressor needs oil, connect the oil pump, oil lines, and oil reservoir to the compressor. Simply start the oil pump and open the compressor’s oil refill valve—this process does not interfere with the compressor’s operation and also helps maintain better hygiene in the data center.


  The issue of unusual noises occurring in vehicles when the air conditioner is used has also been widely criticized by car owners. Due to seasonal limitations, these problems often go unnoticed until it’s too late. The causes of such noises can generally be attributed to several factors: First, an excessive amount of refrigerant may overload the air-conditioning system and result in abnormal noises. In addition, most of these noises stem from the air-conditioning compressor or the blower fan. Measurements have shown that in some vehicles, the noise level from the air conditioner has exceeded 100 decibels, seriously affecting driving and passenger comfort. Industry insiders point out that the noises from the blower fan are mainly caused by the bearings in the fan motor. One possible cause is the poor quality of the bearings themselves; another possibility is that the air-conditioning filter fails to effectively remove dust, allowing dust particles to enter the air ducts and gradually wear down the bearings, leading to axial movement.

345.jpg

Centrifuge image

  No matter how excellent the environment or how properly the equipment is operated, it’s inevitable that the centrifuge will occasionally “act up” with a bit of fuss. Don’t worry—most of the time, these are just minor, routine issues!


  Fault: The centrifuge cannot start in low-speed mode when the temperature is cold—this is due to the lubricating oil solidifying or the lubricant deteriorating, drying up, and becoming sticky. Initially, you can manually help rotate the machine again or clean it thoroughly and then re-lubricate it actively. Severe vibration and loud noise from the centrifuge—check whether the centrifuge is unbalanced; verify that the nuts securing the machine are loose. If so, tighten them securely. Also, inspect the centrifuge bearings for damage or bending. If any damage or bending is found, replace the bearings.


  Check whether the centrifuge’s outer casing is deformed or improperly positioned, causing friction. If so, adjust it accordingly. The sources of vibration in a centrifuge system include: the motor-driven system, screen baskets and manufacturing tolerances, bearings and supports, unbalanced shaft assemblies, cracks or fractures formed externally due to water ingress, overheating failures, severe centrifugal forces, and shaft misalignment at high speeds. When the vibration frequency exceeds the allowable limit, it can trigger resonance throughout the entire centrifuge system, leading to serious consequences. Therefore, whether it’s this centrifuge or any other type of centrifuge, it’s crucial to pay close attention to vibrations during operation, as they significantly impact both the normal functioning and safety of the centrifuge.


  As is well known, Shanghai Luxiangyi Centrifuge Instrument Co., Ltd. has been relentlessly striving for decades, continuously expanding into the centrifuge market and earning a solid reputation through its comprehensive services. In our collaboration, Shanghai Luxiangyi’s high-quality service has been widely recognized and highly praised by our clients.