Laboratory Centrifuge Operating Procedure
Release time:
2017-12-05
Overview:
A laboratory centrifuge is an instrument that uses the centrifugal force generated by a rotating rotor to separate substances of different densities and particle sizes from suspended or emulsified liquids, or to perform analysis concurrently with separation. Laboratory centrifuges have a wide range of applications and are suitable for use in laboratories across various fields, including chemical engineering, food processing, pharmaceuticals, environmental protection, mining, and education. The commonly used laboratory centrifuges typically feature a manual top-discharge three-legged centrifuge design.
Laboratory centrifuge It is an instrument that uses the centrifugal force generated by a rotating rotor to separate substances of different densities and particle sizes from a suspension or emulsion, or to perform analysis concurrently with separation. Laboratory centrifuges have a wide range of applications and are suitable for use in laboratories across various fields, including chemical engineering, food processing, pharmaceuticals, environmental protection, mining, and education. The commonly used laboratory centrifuge typically adopts a manual top-discharge three-legged centrifuge design.
Laboratory Centrifuge Use and Maintenance:
(1) Before using the centrifuge, it must be placed on a stable and sturdy surface (tabletop).
(2) The enclosure must be grounded.
(3) During use, the load must be balanced, and when installing, components must be arranged symmetrically.
(4) When turning on the switch, the speed control knob should be set to the “0” position.
(5) When turning on the switch and adjusting the speed control knob to its maximum setting, the correct procedure is to gradually increase the gear setting of the speed control knob.
(6) After use, turn the speed control knob back to “0” gear by gear, then allow the machine to come to a complete stop on its own. Under no circumstances should you open the machine cover when it is still rotating or while it is powered on.
(7) During use, if you notice any abnormal sounds, immediately turn off the device and have it inspected and repaired.
(8) The commutator and brushes should be inspected regularly (about once a year) for signs of wear. If excessive wear is detected, they should be replaced immediately.
(9) The bearings of the motor should be regularly lubricated with grease.
Laboratory centrifuge Operating procedure:
(1) Open the door cover and symmetrically place the centrifuge tubes from the sample addition area into the rotor.
(2) Turn on the power switch, and preset the rotation speed and working time (Note: During operation, the rotation speed and time can still be adjusted).
(3) Press the start button to begin operation.
(4) When the time reaches zero or the stop button is pressed, the machine will automatically shut down and the buzzer will sound an alarm.
(5) Press the stop button to reset; this is called an emergency stop. Each window will display the last set value.
(6) If you don’t need to change the setpoint, simply press the start button. If you do need to make a change, repeat the operation.
(7) Turn off the power when not in use.
Laboratory centrifuge It can achieve effects such as sedimentation, clarification, concentration, and separation—results of the long-term action of Earth’s gravity. Wiping your hand quickly to remove water droplets from your palm takes advantage of the centrifugal inertial force generated by motion, especially curvilinear motion, thereby achieving rapid separation. In other words, mass generates force through acceleration; high-speed motion or high-speed rotation inevitably speeds up naturally occurring processes. This is precisely how manual spin dryers and centrifugal separation machinery came into being.
Laboratory Centrifuge Use and Maintenance:
(1) Before using the centrifuge, it must be placed on a stable and sturdy surface (tabletop).
(2) The enclosure must be grounded.
(3) During use, the load must be balanced, and when installing, components must be arranged symmetrically.
(4) When turning on the switch, the speed control knob should be set to the “0” position.
(5) When turning on the switch and adjusting the speed control knob to its maximum setting, the correct procedure is to gradually increase the gear setting of the speed control knob.
(6) After use, turn the speed control knob back to “0” gear by gear, then allow the machine to come to a complete stop on its own. Under no circumstances should you open the machine cover when it is still rotating or while it is powered on.
(7) During use, if you notice any abnormal sounds, immediately turn off the device and have it inspected and repaired.
(8) The commutator and brushes should be inspected regularly (about once a year) for signs of wear. If excessive wear is detected, they should be replaced immediately.
(9) The bearings of the motor should be regularly lubricated with grease.
Laboratory centrifuge Operating procedure:
(1) Open the door cover and symmetrically place the centrifuge tubes from the sample addition area into the rotor.
(2) Turn on the power switch, and preset the rotation speed and working time (Note: During operation, the rotation speed and time can still be adjusted).
(3) Press the start button to begin operation.
(4) When the time reaches zero or the stop button is pressed, the machine will automatically shut down and the buzzer will sound an alarm.
(5) Press the stop button to reset; this is called an emergency stop. Each window will display the last set value.
(6) If you don’t need to change the setpoint, simply press the start button. If you do need to make a change, repeat the operation.
(7) Turn off the power when not in use.
Laboratory centrifuge It can achieve effects such as sedimentation, clarification, concentration, and separation—results of the long-term action of Earth’s gravity. Wiping your hand quickly to remove water droplets from your palm takes advantage of the centrifugal inertial force generated by motion, especially curvilinear motion, thereby achieving rapid separation. In other words, mass generates force through acceleration; high-speed motion or high-speed rotation inevitably speeds up naturally occurring processes. This is precisely how manual spin dryers and centrifugal separation machinery came into being.