A centrifuge with accurately controlled rotational speed not only boosts efficiency but also extends the equipment's lifespan.

Release time:

2020-08-11


Overview:

The longevity benefits of centrifuges are inseparable from their scientific operation; common practices include regularly inspecting the equipment and ensuring accurate rotational speeds.

   Centrifuge Prolonging life and enhancing health is inseparable from scientific practices, such as regularly inspecting equipment and ensuring accurate rotational speeds.

  The selection of calibration points for rotational speed can start from the highest calibrated rotational speed and proceed in a linear fashion, taking into account commonly used speeds and selecting as many as possible. If the centrifuge is newly installed or if the test is conducted solely to assess its operational condition, this testing method offers broad coverage and is more feasible and effective. In practice, when centrifuges are used in laboratories, their locations and intended applications tend to be relatively fixed, and the centrifugation conditions set up are also relatively stable. During the calibration process, we specifically target the set rotational speeds of the centrifuge as calibration points (if the centrifuge needs to operate at multiple rotational speeds, we try our best to select each of these speeds as a calibration point).

  After testing, correcting, and confirming, ensure that the centrifuge operates accurately and reliably under all rotational speed conditions encountered during use. The selection of temperature calibration points should, at a minimum, include the set temperatures at which the centrifuge is actually operated. If the calibration points do not encompass the operating conditions of the centrifuge or if necessary corrections and confirmations are not performed, the validity of the calibration will be significantly compromised, and the purpose of calibration will not be achieved.

  The imbalance of the rotor in each centrifuge is unique. The balancing correction of mechanical rotors is a process that involves inspecting and adjusting the distribution of mass within the rotor—a method designed to improve the rotor's mass distribution. By correcting the rotor, the residual imbalance is reduced, ensuring that, at the corresponding operating speed, the residual imbalance, journal vibration, and the load acting on the bearings remain within specified limits.

  Every centrifuge comes with a specified maximum centrifugal force when it leaves the factory. As we all know, during operation, the radius of the rotor and the mass of the sample remain constant; only the rotational speed can be adjusted through control. Therefore, we often tend to describe a centrifuge in terms of its rotational speed—for example, high-speed centrifuge or ultrahigh-speed centrifuge.

  The selection of a centrifuge must involve a comprehensive analysis based on factors such as the size and concentration of solid particles in the suspension (or emulsion), the density difference between solids and liquids (or between two liquids), liquid viscosity, the characteristics of the filter cake (or sediment), and the specific separation requirements. This analysis should ensure that the moisture content of the filter cake (sediment) and the clarity of the filtrate (separated liquid) meet the required standards, allowing for an initial selection of the appropriate type of centrifugal separator. Next, the type and specifications of the centrifuge should be determined according to the processing capacity and the level of automation required for operation, followed by verification through actual trials.

  Next, let’s go into detail about several key operational points for centrifuges:

  Drive: Equipped with a brushless DC motor drive, maintenance-free, featuring high torque and fast lifting speed; a specially designed combined damping system ensures smooth motor operation.

  Speed Control: It takes 14 seconds to accelerate to the maximum speed, and 15 seconds to decelerate from the maximum speed to zero.

  Display: Intelligent control, touch panel

  Refrigeration: Employs imported fluorine-free compressor units and control valves, featuring low vibration, rapid cooling, minimal noise, and compliance with environmental protection requirements. The rotor achieves standby cooling functionality when in a stationary state.

  Body: The body is made of high-quality steel structure, with a stainless steel centrifugal chamber that is sturdy, durable, and easy to clean.

  Rotor: Rotor standby cooling function. The rotor is autoclavable at high pressure (121℃, 20 minutes).

  Security: Equipped with multiple protection features including self-locking door cover, overspeed protection, and imbalance detection, and fitted with an electronic door lock to ensure safe and reliable operation.

  In addition to what has been discussed above, accurate alignment and balanced operation not only promote efficient performance in centrifuges but also serve as a form of protection for the equipment itself. Therefore, in the technical design of instruments across various specifications and applications, the more scientifically sound the balancing design is, the longer the centrifuge’s service life and the higher its operational efficiency will be.