The domestic market for high-speed centrifuges has become increasingly mature.
Release time:
2020-04-24
Overview:
High-speed centrifuge Since its introduction, centrifugation technology has been increasingly widely applied in biological research, significantly accelerating the development of molecular biology. Centrifuges have evolved from ordinary benchtop low-speed models and upright refrigerated ultrahigh-speed units to benchtop refrigerated high-speed models and upright refrigerated ultrahigh-speed units—producing an endless array of products in various models and specifications. The requirements for centrifuge speed, rotors, safety, and technical standards are continually rising.
Typically, these devices include a rotating mechanism, a speed control system, a temperature control system, a vacuum system, a centrifuge chamber, a centrifuge rotor, and safety protection devices. Due to their high rotational speeds, these systems are equipped with low-temperature control units, allowing the temperature of the centrifuge chamber to be precisely adjusted and maintained within the range of 0°C to 40°C. Rotational speed, temperature, and time can all be strictly and accurately controlled, and are displayed either via pointers or digital indicators.
Rotating mechanism: The rotating mechanism of a centrifuge mainly consists of an electric motor, a rotor shaft, and the components connecting them.
Speed Control System: The system consists of components including a standard voltage source, a speed regulator, a current regulator, a power amplifier, an electric motor, and a speed sensor. Commonly used speed sensors include tachogenerators, photoelectric speed sensors, and electromagnetic speed sensors.
Vacuum System: Ultracentrifuges operate at extremely high speeds. When the rotational speed exceeds 4 × 10⁴ rpm, the intense heat generated by air friction becomes a serious issue. Therefore, ultracentrifuges are equipped with vacuum systems that seal and evacuate the centrifuge chamber to eliminate air friction resistance, ensuring that the centrifuge can reach its required operating speed.
Temperature Control System: The temperature of the high-speed centrifuge is controlled by installing a thermocouple in the rotor chamber to monitor the temperature. The refrigeration compressor is fully enclosed and consists of four main components: the compressor, condenser, capillary tube, and evaporator. To reduce noise, the condenser typically employs a water-cooling system. A contact-type thermistor serves as the temperature-sensing element for the temperature controller, and the measurement instrument allows users to select the desired temperature and read out the corresponding temperature control value.
Safety Protection Devices: The safety protection devices for high-speed centrifuges typically include four components: overcurrent protection for the main power supply, overspeed protection for the drive circuit, overload protection for the refrigeration unit, and operational safety protection.
The conditions that a modern high-speed centrifuge should meet include: a reliable, precisely controllable high-speed rotation system; a low-vacuum system to ensure safe operation at speeds exceeding 20,000 r/min and prevent overheating caused by air friction; typically, high-speed centrifuges employ circulating water cooling systems for refrigeration; rotor heads made of high-strength materials such as titanium alloys can withstand the extremely high centrifugal forces generated during ultra-high-speed centrifugation; and effective armored protection to prevent injury in case the rotor were to rupture, thereby containing any flying fragments.
The operating procedures for high-speed centrifuges vary depending on the specific model. However, certain basic guidelines apply universally. First, before starting the centrifuge, all centrifuge tubes—including the centrifuge solution, tube sleeves, and tube caps—must be rigorously balanced. Balancing typically involves injecting a small amount of water into the gap between the outer wall of the centrifuge tube and its sleeve (for ultracentrifuges, this is done using a syringe). When placing the centrifuge tubes into the rotor, they must be positioned precisely according to their pre-balanced weights, ensuring that tubes with marked numbers are placed in the corresponding positions on the rotor. During centrifugation, the rotational speed must never exceed the maximum allowable speed for the rotor. Other centrifugation parameters must also be carefully selected according to the specified requirements. The centrifuge solution should not be filled to the brim to prevent overflow during operation. Additionally, it is crucial to avoid exposing the centrifuge, centrifuge tubes, and associated equipment to corrosive or harmful substances. The rotor of a high-speed centrifuge must be installed strictly according to the manufacturer’s instructions to ensure smooth rotation around the axis. If any malfunction occurs, the centrifuge should be promptly taken to the manufacturer or a qualified repair technician for servicing. Always remember to cover the rotor or the centrifuge chamber with a lid to prevent accidents. Securing the lid tightly helps reduce air resistance at the tube openings during high-speed rotation, thereby alleviating pressure on the machine. It also prevents the formation of negative pressure zones around the rotor, which could cause the rotor to float upward. After centrifugation is complete, use gauze to thoroughly wipe away any accumulated water from the rotor and the centrifuge chamber, then remove the rotor and store it in a dry place.
Although high-speed centrifuges in China possess highly advanced technical features, many users still tend to opt for imported centrifuges, primarily due to the following three factors:
First, many people lack sufficient awareness of domestic centrifuge products: In China, it is deeply ingrained in the subconscious of many individuals that foreign brands are superior to domestic ones. Moreover, these same individuals often criticize the insufficient recognition of domestic brands across various industries. The centrifuge industry is no exception. Such perceptions often lead companies—in many situations—to willingly pay significantly higher prices for foreign centrifuge products rather than opting for high-quality, cost-effective domestic alternatives. People should seek to learn more about domestic centrifuge brands and conduct a comprehensive comparison between domestic and foreign brands, so as to choose products that truly suit their needs. Additionally, domestic centrifuge manufacturers should increase their visibility and exposure, enabling more people to become familiar with and appreciate the quality of Chinese centrifuge products.
Second, the domestic centrifuge industry developed relatively late and currently faces market chaos: In developed countries where industries such as centrifuge manufacturing got off to an early start, research and production of centrifuge technology have been underway for many years, and the industrial chain has become remarkably well-established. However, domestic centrifuge enterprises have only recently begun to develop their technologies and production capabilities, and most of them still operate as small workshops producing single-machine equipment. As a result, their products lack standardized processes and management protocols, leading to some market confusion. Relevant authorities should actively guide centrifuge enterprises, provide support for industry development, and help expand market capacity within a relatively short period of time.
Third, the product lineup is overly homogeneous and the technology is lagging behind: Today, society has increasingly higher demands on the functionality of centrifuges. However, the pace of technological updates for domestic centrifuge products has been relatively slow, and their single application areas can no longer meet the diverse needs of a broad user base. Therefore, to address the challenges posed by different application fields, centrifuge products not only need to undergo continuous upgrades and replacements but also must maximize their diversification to satisfy the specific requirements of various application sectors.
Currently, the domestic high-speed centrifuge industry is experiencing a widespread shortage of skilled talent, and some enterprises are even facing labor shortages. This situation is seriously hindering the development of both the industry and individual companies. Increasing financial investment in the industry can help raise wage levels for workers, thereby attracting more labor and technical talent to join the sector and bringing greater economic benefits to both the industry and its enterprises.
Previous: