How to Make Smart Use of a Centrifuge
Release time:
2017-07-13
Overview:
Centrifuge Its advantages are strikingly evident: it boasts excellent adaptability, a high degree of automation, stable and reliable operation, strong process capability, superb corrosion resistance, a favorable operating environment, fully equipped and highly dependable safety protection devices, and an aesthetically pleasing design. The entire working principle is based on the motion induced by centrifugal force during high-speed rotation, which causes solid particles suspended in a liquid to settle out. Specifically, objects with greater mass or volume in the suspension tend to move toward the region of the rotor with the largest radius, while those with smaller mass or volume tend to deposit closer to the rotor’s inner radius. Centrifuges used in pharmaceutical purification and other refining processes are typically low-speed centrifuges, with rotational speeds below 4,000 rpm and large processing capacities. To meet the GMP standards and requirements for pharmaceutical production, these centrifuges are generally constructed from flat, stainless steel materials. Since the radius of the rotor and the mass of the sample remain constant during operation, only the rotational speed can be adjusted through control. Consequently, we often use rotational speed as a standard way to characterize a centrifuge.
How can you make clever use of a centrifuge?
Currently, electric centrifuges are commonly used in laboratories. Given their high rotational speeds, it is crucial to pay close attention to safety—especially to prevent the centrifuge from moving or even falling off the lab bench during operation due to imbalance or aging of the tube holders. Additionally, one must ensure that the lid is securely closed; otherwise, vibrations could cause the centrifuge tubes to rupture, sending glass fragments flying around and potentially leading to accidents. Therefore, when using a centrifuge, it is essential to follow these operating procedures carefully:
(1) The bottom of the centrifuge tube sleeve must be padded with cotton or a test-tube pad.
(2) If the electric centrifuge makes noise or the machine body vibrates, immediately disconnect the power supply and promptly troubleshoot the issue.
(3) Centrifuge tubes must be placed symmetrically in the rotor to prevent vibration of the machine. If there is only one sample tube, the other tube should be replaced with an equal mass of water.
(4) When starting the centrifuge, you must first close the top cover before slowly starting it up.
(5) After the separation is complete, first turn off the centrifuge. Only after the centrifuge has come to a complete stop may you open the centrifuge lid and remove the sample. Do not use external force to forcibly stop the centrifuge from rotating.
(6) The centrifugation time is generally 1 to 2 minutes; during this period, the experimenter must not leave to attend to other tasks.
Centrifuge Maintenance of:
1) Clean the oil suction pipe filter and the oil tank once a month. If there is too much impurity in the oil, change the oil immediately.
2) Maintenance of the screening basket: The inner surface of the screening basket should be kept conical to ensure that the distance between each point on the screen surface and the spiral scraper remains consistent. This helps ensure uniform wear on the screen surface and extends the service life of the screening basket. Regularly inspect the mesh openings of the screen to prevent blockage and excessive wear caused by centrifugal forces, which can lead to enlargement of the mesh openings. When the mesh openings have expanded to a point where they no longer meet the requirements of the coal washing process, the screening basket should be replaced with a new one.
3) Maintenance of the spiral scraper rotor: Due to prolonged operation, as the scraper blades wear down, the gap between the scraper edges and the screen surface increases, leading to a decline in the machine’s dewatering performance and accelerating wear on the screen basket. To maintain the normal gap of 2 ± mm, a set of adjustment shims is provided between the spindle and the spiral scraper rotor. By adding adjustment shims, the spiral scraper rotor can be raised upward; for every 1 mm increase in shim thickness, the gap between the scraper blades and the screen surface decreases by 0.34 mm. Although the spiral scraper rotor has undergone dynamic balancing tests, prolonged operation can cause uneven wear, resulting in loss of its original balance and significant vibration in the machine. In such cases, the rotor should undergo re-balancing tests. If wear becomes excessive, the rotor should be replaced.
4) Other wear-prone parts: bell cover, material-dividing disc, outlet ring, and feed inlet—replace them promptly if severe wear is detected.
As one of the indispensable pieces of equipment in the pharmaceutical industry, centrifuges have been experiencing rapid growth. Centrifuges are widely used in the medical field—for tasks such as blood separation, virus research, DNA studies, and drug purification. Centrifugation relies on... Centrifuge The powerful centrifugal force generated by the high-speed rotation of the rotor accelerates the sedimentation rate of particles in the liquid, thereby separating substances in the sample that have different sedimentation coefficients and buoyant densities.
How can you make clever use of a centrifuge?
Currently, electric centrifuges are commonly used in laboratories. Given their high rotational speeds, it is crucial to pay close attention to safety—especially to prevent the centrifuge from moving or even falling off the lab bench during operation due to imbalance or aging of the tube holders. Additionally, one must ensure that the lid is securely closed; otherwise, vibrations could cause the centrifuge tubes to rupture, sending glass fragments flying around and potentially leading to accidents. Therefore, when using a centrifuge, it is essential to follow these operating procedures carefully:
(1) The bottom of the centrifuge tube sleeve must be padded with cotton or a test-tube pad.
(2) If the electric centrifuge makes noise or the machine body vibrates, immediately disconnect the power supply and promptly troubleshoot the issue.
(3) Centrifuge tubes must be placed symmetrically in the rotor to prevent vibration of the machine. If there is only one sample tube, the other tube should be replaced with an equal mass of water.
(4) When starting the centrifuge, you must first close the top cover before slowly starting it up.
(5) After the separation is complete, first turn off the centrifuge. Only after the centrifuge has come to a complete stop may you open the centrifuge lid and remove the sample. Do not use external force to forcibly stop the centrifuge from rotating.
(6) The centrifugation time is generally 1 to 2 minutes; during this period, the experimenter must not leave to attend to other tasks.
Centrifuge Maintenance of:
1) Clean the oil suction pipe filter and the oil tank once a month. If there is too much impurity in the oil, change the oil immediately.
2) Maintenance of the screening basket: The inner surface of the screening basket should be kept conical to ensure that the distance between each point on the screen surface and the spiral scraper remains consistent. This helps ensure uniform wear on the screen surface and extends the service life of the screening basket. Regularly inspect the mesh openings of the screen to prevent blockage and excessive wear caused by centrifugal forces, which can lead to enlargement of the mesh openings. When the mesh openings have expanded to a point where they no longer meet the requirements of the coal washing process, the screening basket should be replaced with a new one.
3) Maintenance of the spiral scraper rotor: Due to prolonged operation, as the scraper blades wear down, the gap between the scraper edges and the screen surface increases, leading to a decline in the machine’s dewatering performance and accelerating wear on the screen basket. To maintain the normal gap of 2 ± mm, a set of adjustment shims is provided between the spindle and the spiral scraper rotor. By adding adjustment shims, the spiral scraper rotor can be raised upward; for every 1 mm increase in shim thickness, the gap between the scraper blades and the screen surface decreases by 0.34 mm. Although the spiral scraper rotor has undergone dynamic balancing tests, prolonged operation can cause uneven wear, resulting in loss of its original balance and significant vibration in the machine. In such cases, the rotor should undergo re-balancing tests. If wear becomes excessive, the rotor should be replaced.
4) Other wear-prone parts: bell cover, material-dividing disc, outlet ring, and feed inlet—replace them promptly if severe wear is detected.
As one of the indispensable pieces of equipment in the pharmaceutical industry, centrifuges have been experiencing rapid growth. Centrifuges are widely used in the medical field—for tasks such as blood separation, virus research, DNA studies, and drug purification. Centrifugation relies on... Centrifuge The powerful centrifugal force generated by the high-speed rotation of the rotor accelerates the sedimentation rate of particles in the liquid, thereby separating substances in the sample that have different sedimentation coefficients and buoyant densities.
Previous: