Freezer Centrifuge Cleaning Issues
Release time:
2016-07-19
Overview:
Frozen centrifuge
Frozen centrifuge The issue of cleanliness has long been a major headache for users, as proper cleaning is crucial for product maintenance. Indeed, effective cleaning is the primary factor in maintaining equipment well and extending its service life. When the main power indicator light fails to illuminate, first check whether the indicator light’s fuse and the fuses on the indoor distribution board have blown. Also, ensure that the power cord is making good contact. If a fuse is found to be blown, replace it immediately and make sure the circuit remains unobstructed. Additionally, you should inspect the vacuum pump gauge and oil pressure readings. If the oil pressure is excessively high yet the main unit still fails to start, you must check whether any oil lines are blocked—especially whether the throttle orifices are clear. If they’re blocked, clean them thoroughly to restore unobstructed flow. If the bearings are damaged or their rotation is impeded, if there’s insufficient lubrication inside the bearings, or if excessive dirt has accumulated within the bearings causing increased frictional resistance, resulting in the motor failing to reach its rated speed, you should promptly clean or replace the bearings.
When a refrigerated centrifuge is not used for an extended period or during maintenance, the main power plug should be disconnected. Otherwise, the instrument may remain energized, posing a significant safety risk, especially during maintenance work. To protect the refrigeration compressor, the interval between turning the refrigerated centrifuge off and on must be at least 3 minutes; otherwise, the compressor could be damaged. When the rotor is not in use, it should be removed from the centrifuge chamber and promptly cleaned with a neutral detergent and thoroughly dried to prevent chemical corrosion. Store the rotor in a dry, well-ventilated area. Do not use non-neutral cleaning agents to clean the rotor, nor use electric hot-air blowers (drying devices) to dry it. A small amount of lubricant should be applied to the central bore of the rotor to provide protection. Before using the rotor in a refrigerated centrifuge, always verify that the correct rotor number has been set. An incorrect rotor number setting can result in the rotor being operated at excessive speeds or failing to achieve the desired centrifugal effect. In particular, operating the rotor at excessively high speeds could lead to a catastrophic rotor rupture—such an accident must never be taken lightly.
Insert the centrifuge tubes—containing the substances to be separated—into the corresponding holes in the centrifuge rotor. Frozen centrifuge To further study biochemistry, separate large quantities of substances, clean the cavity and rotor of the refrigerated centrifuge, and remove any condensation water inside the cavity, after use, be sure to leave the door open until the cavity returns to room temperature. Before centrifugation, ensure that samples are balanced. After centrifugation, pay close attention to disinfection and sterilization. If necessary, pre-cool the rotor. Properly maintain and store rotors, and take care to protect the counting ring at the bottom.
When a refrigerated centrifuge is running, the refrigeration system causes moisture in the air to condense into frost inside the centrifuge chamber. After the machine is turned off, this frost melts into water. Since there are no drain holes, the water gradually accumulates in the centrifuge chamber. In such cases, users should remove the rotor themselves and carefully clean out the accumulated water. When reassembling the rotor, make sure it is securely installed to prevent accidents. Aluminum alloys are susceptible to corrosion: Centrifuge rotors made of aluminum alloy tend to lose strength when corroded, increasing the risk of accidents. Aluminum alloys are easily corroded by liquids; after cleaning, they should be thoroughly dried using a hairdryer or by turning them upside down for a while until completely dry before use. Some refrigerated centrifuges are imported by blood banks. Frozen centrifuge The six plastic trays that should have been placed in the six aluminum cups are missing. The plastic trays are meant to hold blood bags, so as to avoid placing the blood bags directly into the aluminum cups. Also, be sure to check whether the test tubes have any cracks. If a test tube—especially one that has been used repeatedly—shows even the slightest crack, it must never be used. Otherwise, during use, a cracked test tube could cause an imbalance during rotor rotation, potentially leading to serious accidents such as shaft breakage.
When a refrigerated centrifuge is not used for an extended period or during maintenance, the main power plug should be disconnected. Otherwise, the instrument may remain energized, posing a significant safety risk, especially during maintenance work. To protect the refrigeration compressor, the interval between turning the refrigerated centrifuge off and on must be at least 3 minutes; otherwise, the compressor could be damaged. When the rotor is not in use, it should be removed from the centrifuge chamber and promptly cleaned with a neutral detergent and thoroughly dried to prevent chemical corrosion. Store the rotor in a dry, well-ventilated area. Do not use non-neutral cleaning agents to clean the rotor, nor use electric hot-air blowers (drying devices) to dry it. A small amount of lubricant should be applied to the central bore of the rotor to provide protection. Before using the rotor in a refrigerated centrifuge, always verify that the correct rotor number has been set. An incorrect rotor number setting can result in the rotor being operated at excessive speeds or failing to achieve the desired centrifugal effect. In particular, operating the rotor at excessively high speeds could lead to a catastrophic rotor rupture—such an accident must never be taken lightly.
Insert the centrifuge tubes—containing the substances to be separated—into the corresponding holes in the centrifuge rotor. Frozen centrifuge To further study biochemistry, separate large quantities of substances, clean the cavity and rotor of the refrigerated centrifuge, and remove any condensation water inside the cavity, after use, be sure to leave the door open until the cavity returns to room temperature. Before centrifugation, ensure that samples are balanced. After centrifugation, pay close attention to disinfection and sterilization. If necessary, pre-cool the rotor. Properly maintain and store rotors, and take care to protect the counting ring at the bottom.
When a refrigerated centrifuge is running, the refrigeration system causes moisture in the air to condense into frost inside the centrifuge chamber. After the machine is turned off, this frost melts into water. Since there are no drain holes, the water gradually accumulates in the centrifuge chamber. In such cases, users should remove the rotor themselves and carefully clean out the accumulated water. When reassembling the rotor, make sure it is securely installed to prevent accidents. Aluminum alloys are susceptible to corrosion: Centrifuge rotors made of aluminum alloy tend to lose strength when corroded, increasing the risk of accidents. Aluminum alloys are easily corroded by liquids; after cleaning, they should be thoroughly dried using a hairdryer or by turning them upside down for a while until completely dry before use. Some refrigerated centrifuges are imported by blood banks. Frozen centrifuge The six plastic trays that should have been placed in the six aluminum cups are missing. The plastic trays are meant to hold blood bags, so as to avoid placing the blood bags directly into the aluminum cups. Also, be sure to check whether the test tubes have any cracks. If a test tube—especially one that has been used repeatedly—shows even the slightest crack, it must never be used. Otherwise, during use, a cracked test tube could cause an imbalance during rotor rotation, potentially leading to serious accidents such as shaft breakage.