Recommendations for Using Biological Serum Centrifuges
Release time:
2014-08-04
Overview:
Flocculent precipitates: There are various causes for their formation, but they do not affect the quality of the serum itself. Unless it is necessary to reduce these precipitates, they can be removed by centrifuging at 3000 rpm for 5 minutes. Alternatively, after centrifugation, the supernatant can be collected and added directly to the culture medium for simultaneous sterilization and filtration.
1. Serum must be stored at -20℃. If stored at 4℃, do not keep it for more than two weeks. For certain institutions that cannot use an entire bottle at once, the serum can be aseptically aliquoted into sterile 50-mL centrifuge tubes at a concentration of 40-45%. Since the volume of serum increases by approximately 10% upon thawing, sufficient space must be reserved to accommodate this expansion; otherwise, contamination or rupture of the container due to freezing may easily occur.
2. Serum is typically available in 200 ml and 400 ml volumes. Therefore, we recommend that you thaw the serum gradually during use: first, thaw it at 4°C in a refrigerator or cold storage facility for 24 hours (-20°C → 4°C); then, allow it to fully dissolve at room temperature before aliquoting it into sterile centrifuge tubes. Generally, each aliquot should contain 40–45 ml of serum, dispensed into 50 ml sterile centrifuge tubes. We strongly advise you to shake the serum thoroughly and regularly throughout the entire process, taking care not to introduce air bubbles. This ensures uniform temperature and composition, thereby minimizing the formation of precipitates. Do not thaw the serum directly from -20°C to 37°C, as such a drastic temperature change can easily cause protein denaturation and precipitation.
3. Heat-inactivation of serum generally refers to heating fully thawed serum at 56°C for 30 minutes in a water bath, during which the serum must be shaken regularly and uniformly. The purpose of this treatment is to inactivate complement components in the serum. However, heat-inactivated serum tends to exhibit a significant increase in precipitation and may compromise serum quality. Therefore, fetal bovine serum used for cell culture is not subjected to heat-inactivation. In contrast, serum used for diagnostic reagents undergoes heat-inactivation prior to sterile filtration.
4. When using serum, do not leave it at 37℃ for too long. The serum will become turbid, and many of its less stable components will be degraded, thereby affecting the serum’s quality.
5. Both fetal bovine serum intended for highly confluent cell cultures and fetal bovine serum intended for standard cell cultures must undergo sterile filtration through a 100-nanometer filter three consecutive times to remove mycoplasma. If suspended particles are detected in the serum product, unless removal is absolutely necessary, it is recommended to filter the serum together with the culture medium rather than filtering the serum directly.
6. Precipitate in serum
6.1 Flocculent Particles: There are several causes for their formation, but the most common ones are the denaturation of lipoproteins in the serum and the presence of fibrin in the serum after thawing. These flocculent precipitates do not affect the quality of the serum itself. Unless it is necessary to reduce these precipitates, they can be removed by centrifugation at 3,000 rpm for 5 minutes. Alternatively, after centrifugation, the supernatant can be collected and filtered together with the culture medium to remove any remaining particles.
2. Under microscopic examination, “small black dots” often appear more prominently in serum that has undergone heat treatment, accompanied by an increased formation of precipitates. Some of these precipitates, when viewed under a microscope, resemble “small black dots” and are frequently mistaken for serum contamination. As a result, the serum is sometimes incubated at 37℃ in an attempt to culture these “microorganisms.” However, at 37℃, the precipitate formation actually intensifies further, leading to a misinterpretation of microbial proliferation. Yet, when tested using standard bacterial culture media, no contamination is detected. Generally speaking, these small black dots do not affect cell growth.
2. Serum is typically available in 200 ml and 400 ml volumes. Therefore, we recommend that you thaw the serum gradually during use: first, thaw it at 4°C in a refrigerator or cold storage facility for 24 hours (-20°C → 4°C); then, allow it to fully dissolve at room temperature before aliquoting it into sterile centrifuge tubes. Generally, each aliquot should contain 40–45 ml of serum, dispensed into 50 ml sterile centrifuge tubes. We strongly advise you to shake the serum thoroughly and regularly throughout the entire process, taking care not to introduce air bubbles. This ensures uniform temperature and composition, thereby minimizing the formation of precipitates. Do not thaw the serum directly from -20°C to 37°C, as such a drastic temperature change can easily cause protein denaturation and precipitation.
3. Heat-inactivation of serum generally refers to heating fully thawed serum at 56°C for 30 minutes in a water bath, during which the serum must be shaken regularly and uniformly. The purpose of this treatment is to inactivate complement components in the serum. However, heat-inactivated serum tends to exhibit a significant increase in precipitation and may compromise serum quality. Therefore, fetal bovine serum used for cell culture is not subjected to heat-inactivation. In contrast, serum used for diagnostic reagents undergoes heat-inactivation prior to sterile filtration.
4. When using serum, do not leave it at 37℃ for too long. The serum will become turbid, and many of its less stable components will be degraded, thereby affecting the serum’s quality.
5. Both fetal bovine serum intended for highly confluent cell cultures and fetal bovine serum intended for standard cell cultures must undergo sterile filtration through a 100-nanometer filter three consecutive times to remove mycoplasma. If suspended particles are detected in the serum product, unless removal is absolutely necessary, it is recommended to filter the serum together with the culture medium rather than filtering the serum directly.
6. Precipitate in serum
6.1 Flocculent Particles: There are several causes for their formation, but the most common ones are the denaturation of lipoproteins in the serum and the presence of fibrin in the serum after thawing. These flocculent precipitates do not affect the quality of the serum itself. Unless it is necessary to reduce these precipitates, they can be removed by centrifugation at 3,000 rpm for 5 minutes. Alternatively, after centrifugation, the supernatant can be collected and filtered together with the culture medium to remove any remaining particles.
2. Under microscopic examination, “small black dots” often appear more prominently in serum that has undergone heat treatment, accompanied by an increased formation of precipitates. Some of these precipitates, when viewed under a microscope, resemble “small black dots” and are frequently mistaken for serum contamination. As a result, the serum is sometimes incubated at 37℃ in an attempt to culture these “microorganisms.” However, at 37℃, the precipitate formation actually intensifies further, leading to a misinterpretation of microbial proliferation. Yet, when tested using standard bacterial culture media, no contamination is detected. Generally speaking, these small black dots do not affect cell growth.