Low-speed centrifuges have a wide range of applications.

Release time:

2015-10-23


Overview:

Low-speed centrifuge

   Low-speed centrifuge It’s simply a general term for centrifuges used in experiments. The reason it’s called a “low-speed centrifuge” is that the rotor speed of such centrifuges is below 5,000 revolutions per minute. The naming convention varies depending on the rotor speed, and the experimental requirements also differ accordingly. With their reasonably designed structure, low-speed centrifuges are widely used in fields such as clinical medicine, biochemistry, immunology, blood banks, and other areas. They are standard laboratory instruments commonly employed for centrifuging and precipitating samples.
  The low-speed centrifuge can be described as an industry favorite—after all, it’s highly versatile and valuable. It’s not simply that rarity drives its value. Below, I’ll briefly illustrate this with some examples:
  Using a low-speed centrifuge to extract DNA is a simple and rapid method. However, if the sample contains large amounts of substances such as nucleotides or proteins that can absorb ultraviolet light, the measurement error will be significant; therefore, these interfering substances should be removed in advance whenever possible. In this experiment, we used a benchtop low-speed centrifuge to centrifuge and separate nucleotides, proteins, and other similar substances, thereby achieving purification. We recommend our factory’s benchtop low-speed centrifuge for this purpose; this experiment will take this centrifuge as an example.
  Operating instructions:
  1. Place 3 g of dry yeast powder into an Erlenmeyer flask, add 30 ml of 2 g/L NaOH solution, cool it down, and then adjust the pH to around 4.0 using acetic acid. Next, add another 30 ml of NaOH solution (approximately 28 g), heat in a boiling water bath for 30 minutes, and stir continuously throughout the process.

  2. Add 20–40 ml of 95% ethanol. The amount added should be sufficient to cause visible turbidity under the naked eye. Centrifuge at 3,000 rpm for 10 minutes, then discard the supernatant.
  3. Add 15 ml of water to the precipitate and dissolve it. Then, add 15 ml of a chloroform-isopentyl alcohol mixture (chloroform:isopentyl alcohol = 24:1), shake for 20 minutes, and centrifuge using a benchtop low-speed centrifuge (3000 rpm, 10 minutes).
  4. Carefully pipette the upper aqueous phase, measure its volume, and add potassium acetate powder to achieve a final concentration of 2% potassium acetate. Then, add twice the volume of ethanol to the above solution, mix thoroughly, and place the mixture in an ice bath for 20–30 minutes to allow RNA to precipitate as a flocculent pellet.
  At 5,300 rpm, centrifuge using a desktop low-speed centrifuge for 20 minutes to collect the precipitate, thereby obtaining crude RNA.
  A low-speed centrifuge is also a commonly used device in autologous cell wrinkle-reduction procedures. The PRP autologous cell rejuvenation technique is a well-established clinical cosmetic procedure that has undergone extensive clinical validation and proven to be effective. Moreover, since the raw materials are derived from the patient’s own blood, this treatment does not trigger any rejection or allergic reactions. The rejuvenation procedure can be easily completed in just 30 minutes. After treatment, there are no wounds on the skin, so you can resume your work and daily activities without any disruption—allowing you to regain your youthful appearance completely unnoticed. Next, experts from the plastic surgery hospital will walk us through the step-by-step process of the PRP autologous cell rejuvenation treatment.
  PRP Autologous Cell Rejuvenation Treatment Procedure
  1. After cleaning and disinfecting the area, the medical assistant will draw 10–20 ml of your blood from the vein in your elbow. This step is identical to the blood draw performed during a routine physical exam and takes only about 5 minutes to complete, with only a slight sensation of pain.
  2. The doctor will use a centrifuge with a centrifugal force of 3,000 G to separate the various components of the blood. This step typically takes about 10 to 20 minutes. Afterward, the blood will be separated into four distinct layers: plasma, white blood cells, platelets, and red blood cells.
  3. The PRP kit equipped with patented technology solves the problems associated with previous PRP preparation methods—namely, their complex procedures, cumbersome setup requirements, and lengthy production cycles. With just one specialized kit, physicians can immediately extract platelets containing high concentrations of platelets and high concentrations of growth factors on-site.
  4. Finally, the doctor will inject the growth factors back into the skin of the area you’d like to improve. This procedure is painless and typically takes only 10 to 20 minutes.
  Experts from plastic surgery hospitals explain that the PRP autologous cell rejuvenation procedure provides comprehensive lifting and regeneration of the entire skin layer, effectively enhancing skin texture, collagen, and elastin fibers. Low-speed centrifuge Carry out comprehensive repairs and reassembly.