Method for extracting genomic DNA from animal tissue cells

Release time:

2014-03-03


Overview:

Constant-temperature water bath, benchtop centrifuge, UV spectrophotometer (GeneQuant), pipettes, glass homogenizer, sterilized centrifuge tubes, sterilized pipette tips

I. Experimental Principle
All nucleated cells of eukaryotic organisms—including cultured cells—can be used to prepare genomic DNA. In eukaryotic cells, DNA is stored in the nucleus in the form of chromosomes. Therefore, the principle behind DNA preparation is to both separate DNA from proteins, lipids, and carbohydrates and preserve the integrity of the DNA molecules themselves. The general procedure for DNA extraction involves first digesting and breaking down proteins in a solution containing SDS (sodium dodecyl sulfate) and proteinase K, after which proteins are separated by phenol and chloroform/isopentanol extraction. The resulting DNA solution is then subjected to ethanol precipitation, causing the DNA to precipitate out of the solution.
An important characteristic of Proteinase K is its ability to maintain high activity even in the presence of SDS and EDTA (disodium ethylenediaminetetraacetate). In the reaction system used for DNA extraction after tissue homogenization, SDS can disrupt cell membranes and nuclear membranes, thereby separating tissue proteins from DNA; EDTA, on the other hand, inhibits the activity of DNases present in cells. Meanwhile, Proteinase K degrades proteins into small peptides or amino acids, allowing the DNA molecules to be completely liberated.
II. Instruments and Reagents
1. Instrument:
Constant-temperature water bath, benchtop centrifuge, UV spectrophotometer (GeneQuant), pipettes, glass homogenizer, sterilized centrifuge tubes, sterilized pipette tips

3. Operating Steps
1. Take 0.1 g (0.5 cm³) of fresh or frozen animal tissue, and mince it as finely as possible. Transfer the minced tissue into a glass homogenizer, add 1 ml of cell lysis buffer, and homogenize until no tissue pieces are visible. Then transfer the homogenate into a 1.5 ml centrifuge tube, add 20 μl of proteinase K (500 μg/ml), and mix thoroughly. Incubate in a 65℃ water bath for 30 minutes; alternatively, you can place the sample in a 37℃ water bath for 12–24 hours, with intermittent shaking and occasional inversion of the centrifuge tube several times. Centrifuge at 12,000 rpm for 5 minutes using a benchtop centrifuge, and carefully transfer the supernatant into another centrifuge tube.
2. Add twice the volume of isopropanol, invert and mix thoroughly. You should then observe filamentous material. Use a 100-μl pipette tip to carefully pick up the material, allow it to air-dry, and then redissolve it in 200 μl of TE buffer. (If further purification is required—for applications such as PCR reactions—proceed according to the steps below.)
3. Add an equal volume of phenol:chloroform:isoamyl alcohol, shake thoroughly to mix, and centrifuge at 12,000 rpm for 5 minutes.
4. Transfer the upper-layer solution to another tube, add an equal volume of chloroform-isopentyl alcohol, shake vigorously to mix thoroughly, and centrifuge at 12,000 rpm for 5 minutes.
5. Transfer the upper-layer solution to another tube, add 1/2 volume of 7.5 mol/L ammonium acetate, then add twice the volume of anhydrous ethanol. After thorough mixing, allow the mixture to precipitate at room temperature for 2 minutes, followed by centrifugation at 12,000 rpm for 10 minutes.
6. Carefully discard the supernatant, invert the centrifuge tube onto absorbent paper, and remove any residual droplets adhering to the tube walls.
7. Wash the precipitate once with 1 ml of 70% ethanol, then centrifuge at 12,000 rpm for 5 minutes.
8. Carefully discard the supernatant, invert the centrifuge tube onto absorbent paper to remove any residual droplets adhering to the tube walls, and allow it to air-dry at room temperature.

9. Add 200 μl of TE to redissolve the precipitate, then store it at 4℃ or -20℃ for future use.
10. Take an appropriate amount of sample and use the GeneQuant to determine its concentration and purity.
IV. Frequently Asked Questions
1. The experimental materials selected should be fresh, and the processing time should not be too long.
2. Before adding the cell lysis buffer, the cells must be evenly dispersed to minimize the formation of DNA aggregates.
3. The extracted DNA is difficult to dissolve: it is impure and contains a high level of contaminants; too little lysis buffer was added, resulting in an excessively high concentration. If the precipitate is too dry, it will also make dissolution very challenging.
4. During electrophoresis, the DNA appears smeared: This may be due to careless handling or contamination with nucleases and other substances.
5. In spectrophotometric analysis, if the A280/A260 ratio of DNA is less than 1.8, it indicates impurity and the presence of contaminants such as proteins. In this case, SDS should be added to a final concentration of 0.5%, and steps 2 through 8 should be repeated.
6. After phenol/chloroform/isopentyl alcohol extraction, the supernatant becomes too viscous and difficult to pipette: This indicates a high DNA concentration. You can increase the volume of the buffer used prior to extraction or reduce the amount of tissue sampled.